CarbonRing1-2pinmodslessfocus.RTN ================================================================================ Header: Carbon Ring #2 with changed origin and axis ,midpoint between midpoints on pi All measurements are done after the origin and axis are set -------------------------------------------------------------------------------- Setup: Quick locate left and right 6.5mm holes with circle target and origin , axis Place hot glue @ 4 places between 3,4 9,10 15,16 21,22 apply glue without letting tip touch ring, let glue flow under part Take shim measurements under all the carbon tabs touching the table Ring is on table with flat carbon washers towards glass 3.5mm pins into 4 side holes on tabs ================================================================================ Step: 1 MM Cart Decimal Degree Measure Comment: Top pin Measure for origin Point Actual Nominal Upper Tol. Lower Tol. X Location +178.5284 +178.5379 +00.0000 +00.0000 Y Location +180.0409 +180.0409 +00.0000 +00.0000 Z Location -006.0336 -006.0256 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 2 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 1 -------------------------------------------------------------------------------- Step: 3 MM Cart Decimal Degree Measure XY Plane Line Actual Nominal Upper Tol. Lower Tol. Angle -090.6914 +000.0000 +00.0000 +00.0000 X Location +178.1848 +000.0000 +00.0000 +00.0000 Y Location +179.9651 +000.0000 +00.0000 +00.0000 Z Location +000.0006 +000.0000 +00.0000 +00.0000 Straightness +000.0025 +00.0000 Lens: 1x Points: 12 Data Stream: No -------------------------------------------------------------------------------- Step: 4 MM Cart Decimal Degree Measure XY Plane Line Actual Nominal Upper Tol. Lower Tol. Angle +089.3039 +000.0000 +00.0000 +00.0000 X Location +181.6738 +000.0000 +00.0000 +00.0000 Y Location +180.0022 +000.0000 +00.0000 +00.0000 Z Location +000.0006 +000.0000 +00.0000 +00.0000 Straightness +000.0025 +00.0000 Lens: 1x Points: 13 Data Stream: No -------------------------------------------------------------------------------- Step: 5 MM Cart Decimal Degree Measure Comment: right pin Measure for origin Point Actual Nominal Upper Tol. Lower Tol. X Location +360.0572 +360.0452 +00.0000 +00.0000 Y Location +001.4125 +001.4130 +00.0000 +00.0000 Z Location -000.0179 -000.0114 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 6 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 5 -------------------------------------------------------------------------------- Step: 7 MM Cart Decimal Degree Measure XY Plane Line Actual Nominal Upper Tol. Lower Tol. Angle -179.8387 +000.0000 +00.0000 +00.0000 X Location +360.1440 +000.0000 +00.0000 +00.0000 Y Location +001.7177 +000.0000 +00.0000 +00.0000 Z Location +000.0005 +000.0000 +00.0000 +00.0000 Straightness +000.0020 +00.0000 Lens: 1x Points: 12 Data Stream: No -------------------------------------------------------------------------------- Step: 8 MM Cart Decimal Degree Measure XY Plane Line Actual Nominal Upper Tol. Lower Tol. Angle +000.1415 +000.0000 +00.0000 +00.0000 X Location +360.1558 +000.0000 +00.0000 +00.0000 Y Location -001.7666 +000.0000 +00.0000 +00.0000 Z Location +000.0005 +000.0000 +00.0000 +00.0000 Straightness +000.0017 +00.0000 Lens: 1x Points: 13 Data Stream: No -------------------------------------------------------------------------------- Step: 9 MM Cart Decimal Degree Measure Comment: Bottom pin measure for origin Point Actual Nominal Upper Tol. Lower Tol. X Location +181.3539 +181.3547 +00.0000 +00.0000 Y Location -179.9499 -179.9499 +00.0000 +00.0000 Z Location -000.0489 -000.1252 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 10 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 9 -------------------------------------------------------------------------------- Step: 11 MM Cart Decimal Degree Measure XY Plane Line Actual Nominal Upper Tol. Lower Tol. Angle +089.8900 +000.0000 +00.0000 +00.0000 X Location +181.7981 +000.0000 +00.0000 +00.0000 Y Location -179.9718 +000.0000 +00.0000 +00.0000 Z Location +000.0004 +000.0000 +00.0000 +00.0000 Straightness +000.0018 +00.0000 Lens: 1x Points: 12 Data Stream: No -------------------------------------------------------------------------------- Step: 12 MM Cart Decimal Degree Measure XY Plane Line Actual Nominal Upper Tol. Lower Tol. Angle -090.1034 +000.0000 +00.0000 +00.0000 X Location +178.3100 +000.0000 +00.0000 +00.0000 Y Location -180.0314 +000.0000 +00.0000 +00.0000 Z Location +000.0024 +000.0000 +00.0000 +00.0000 Straightness +000.0019 +00.0000 Lens: 1x Points: 12 Data Stream: No -------------------------------------------------------------------------------- Step: 13 MM Cart Decimal Degree Measure Comment: Left pim measure for origin Point Actual Nominal Upper Tol. Lower Tol. X Location +000.0374 +000.0596 +00.0000 +00.0000 Y Location -001.2770 -001.2775 +00.0000 +00.0000 Z Location +000.0562 +000.0190 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 14 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 13 -------------------------------------------------------------------------------- Step: 15 MM Cart Decimal Degree Measure XY Plane Line Actual Nominal Upper Tol. Lower Tol. Angle -000.1046 +000.0000 +00.0000 +00.0000 X Location +000.1780 +000.0000 +00.0000 +00.0000 Y Location -001.7714 +000.0000 +00.0000 +00.0000 Z Location +000.0007 +000.0000 +00.0000 +00.0000 Straightness +000.0015 +00.0000 Lens: 1x Points: 13 Data Stream: No -------------------------------------------------------------------------------- Step: 16 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +178.0775 +000.0000 +00.0000 +00.0000 Y Location +190.4455 +000.0000 +00.0000 +00.0000 Z Location +000.0346 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 17 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 16 -------------------------------------------------------------------------------- Step: 18 MM Cart Decimal Degree Measure XY Plane Line Actual Nominal Upper Tol. Lower Tol. Angle -090.6756 +000.0000 +00.0000 +00.0000 X Location +178.2869 +000.0000 +00.0000 +00.0000 Y Location +189.9033 +000.0000 +00.0000 +00.0000 Z Location +000.0006 +000.0000 +00.0000 +00.0000 Straightness +000.0003 +00.0000 Lens: 1x Points: 7 Data Stream: No -------------------------------------------------------------------------------- Step: 19 MM Cart Decimal Degree Measure XY Plane Line Actual Nominal Upper Tol. Lower Tol. Angle +089.3252 +000.0000 +00.0000 +00.0000 X Location +181.7725 +000.0000 +00.0000 +00.0000 Y Location +189.7799 +000.0000 +00.0000 +00.0000 Z Location +000.0006 +000.0000 +00.0000 +00.0000 Straightness +000.0008 +00.0000 Lens: 1x Points: 6 Data Stream: No -------------------------------------------------------------------------------- Step: 20 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +370.8630 +000.0000 +00.0000 +00.0000 Y Location +001.8956 +000.0000 +00.0000 +00.0000 Z Location -000.0521 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 21 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 20 -------------------------------------------------------------------------------- Step: 22 MM Cart Decimal Degree Measure XY Plane Line Actual Nominal Upper Tol. Lower Tol. Angle -179.8418 +000.0000 +00.0000 +00.0000 X Location +370.6571 +000.0000 +00.0000 +00.0000 Y Location +001.7681 +000.0000 +00.0000 +00.0000 Z Location +000.0006 +000.0000 +00.0000 +00.0000 Straightness +000.0009 +00.0000 Lens: 1x Points: 9 Data Stream: No -------------------------------------------------------------------------------- Step: 23 MM Cart Decimal Degree Measure XY Plane Line Actual Nominal Upper Tol. Lower Tol. Angle +000.1826 +000.0000 +00.0000 +00.0000 X Location +370.8566 +000.0000 +00.0000 +00.0000 Y Location -001.7138 +000.0000 +00.0000 +00.0000 Z Location +000.0006 +000.0000 +00.0000 +00.0000 Straightness +000.0009 +00.0000 Lens: 1x Points: 9 Data Stream: No -------------------------------------------------------------------------------- Step: 24 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +182.0905 +000.0000 +00.0000 +00.0000 Y Location -190.2513 +000.0000 +00.0000 +00.0000 Z Location -000.0224 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 25 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 24 -------------------------------------------------------------------------------- Step: 26 MM Cart Decimal Degree Measure XY Plane Line Actual Nominal Upper Tol. Lower Tol. Angle +089.8901 +000.0000 +00.0000 +00.0000 X Location +181.7957 +000.0000 +00.0000 +00.0000 Y Location -189.8329 +000.0000 +00.0000 +00.0000 Z Location +000.0001 +000.0000 +00.0000 +00.0000 Straightness +000.0003 +00.0000 Lens: 1x Points: 6 Data Stream: No -------------------------------------------------------------------------------- Step: 27 MM Cart Decimal Degree Measure XY Plane Line Actual Nominal Upper Tol. Lower Tol. Angle -090.1172 +000.0000 +00.0000 +00.0000 X Location +178.3081 +000.0000 +00.0000 +00.0000 Y Location -190.1847 +000.0000 +00.0000 +00.0000 Z Location +000.0006 +000.0000 +00.0000 +00.0000 Straightness +000.0003 +00.0000 Lens: 1x Points: 7 Data Stream: No -------------------------------------------------------------------------------- Step: 28 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -010.2147 +000.0000 +00.0000 +00.0000 Y Location -002.0092 +000.0000 +00.0000 +00.0000 Z Location +000.0585 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 29 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 28 -------------------------------------------------------------------------------- Step: 30 MM Cart Decimal Degree Measure XY Plane Line Actual Nominal Upper Tol. Lower Tol. Angle -000.1013 +000.0000 +00.0000 +00.0000 X Location -010.1990 +000.0000 +00.0000 +00.0000 Y Location -001.7727 +000.0000 +00.0000 +00.0000 Z Location +000.0005 +000.0000 +00.0000 +00.0000 Straightness +000.0004 +00.0000 Lens: 1x Points: 8 Data Stream: No -------------------------------------------------------------------------------- Step: 31 MM Cart Decimal Degree Measure XY Plane Line Actual Nominal Upper Tol. Lower Tol. Angle +179.8427 +000.0000 +00.0000 +00.0000 X Location -009.9039 +000.0000 +00.0000 +00.0000 Y Location +001.7106 +000.0000 +00.0000 +00.0000 Z Location +000.0005 +000.0000 +00.0000 +00.0000 Straightness +000.0012 +00.0000 Lens: 1x Points: 7 Data Stream: No -------------------------------------------------------------------------------- Step: 32 MM Cart Decimal Degree Construct Comment: top pin outside midpoint Midpoint Actual Nominal Upper Tol. Lower Tol. p 3-D Distance +003.4878 +003.4884 +00.0000 +00.0000 p X Location +180.0297 +180.0301 +00.0000 +00.0000 p Y Location +189.8416 +189.8416 +00.0000 +00.0000 Z Location +000.0165 +000.0465 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 18 19 -------------------------------------------------------------------------------- Step: 33 MM Cart Decimal Degree Construct Comment: Right pin outside midpoint Midpoint Actual Nominal Upper Tol. Lower Tol. p 3-D Distance +003.4875 +003.4884 +00.0000 +00.0000 p X Location +370.7568 +370.7531 +00.0000 +00.0000 p Y Location +000.0272 +000.0275 +00.0000 +00.0000 Z Location -000.0355 -000.0215 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 22 23 -------------------------------------------------------------------------------- Step: 34 MM Cart Decimal Degree Construct Comment: Bottom pin outside midpoint Midpoint Actual Nominal Upper Tol. Lower Tol. p 3-D Distance +003.5053 +003.5062 +00.0000 +00.0000 p X Location +180.0519 +180.0522 +00.0000 +00.0000 p Y Location -190.0088 -190.0088 +00.0000 +00.0000 Z Location -000.0582 -000.0195 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 26 27 -------------------------------------------------------------------------------- Step: 35 MM Cart Decimal Degree Construct Comment: Left pin outside midpoint Midpoint Actual Nominal Upper Tol. Lower Tol. p 3-D Distance +003.4957 +003.4966 +00.0000 +00.0000 p X Location -010.0515 -010.0544 +00.0000 +00.0000 p Y Location -000.0310 -000.0311 +00.0000 +00.0000 Z Location +000.0005 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 31 30 -------------------------------------------------------------------------------- Step: 36 MM Cart Decimal Degree Measure XY Plane Line Actual Nominal Upper Tol. Lower Tol. Angle +179.9050 +000.0000 +00.0000 +00.0000 X Location +000.0814 +000.0000 +00.0000 +00.0000 Y Location +001.7117 +000.0000 +00.0000 +00.0000 Z Location -000.0030 +000.0000 +00.0000 +00.0000 Straightness +000.0019 +00.0000 Lens: 1x Points: 12 Data Stream: No -------------------------------------------------------------------------------- Step: 37 MM Cart Decimal Degree Construct Comment: Top pin midpoint for origin Midpoint Actual Nominal Upper Tol. Lower Tol. 3-D Distance +003.4892 +003.4890 +00.0000 +00.0000 p X Location +179.9293 +179.9241 +00.0000 +00.0000 p Y Location +179.9837 +179.9835 +00.0000 +00.0000 Z Location -000.0075 -000.0207 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 4 3 -------------------------------------------------------------------------------- Step: 38 MM Cart Decimal Degree Construct Comment: Right pim midpoint for origin Midpoint Actual Nominal Upper Tol. Lower Tol. 3-D Distance +003.4843 +003.4841 +00.0000 +00.0000 p X Location +360.1499 +360.1397 +00.0000 +00.0000 p Y Location -000.0245 -000.0262 +00.0000 +00.0000 Z Location -000.0255 -000.0020 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 8 7 -------------------------------------------------------------------------------- Step: 39 MM Cart Decimal Degree Construct Comment: Bottom pin midpoint for orign Midpoint Actual Nominal Upper Tol. Lower Tol. 3-D Distance +003.4887 +003.4886 +00.0000 +00.0000 p X Location +180.0541 +180.0554 +00.0000 +00.0000 p Y Location -180.0016 -180.0015 +00.0000 +00.0000 Z Location -000.0735 -000.1087 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 11 12 -------------------------------------------------------------------------------- Step: 40 MM Cart Decimal Degree Construct Comment: Left pin midpoint for orign Midpoint Actual Nominal Upper Tol. Lower Tol. 3-D Distance +003.4845 +003.4877 +00.0000 +00.0000 p X Location +000.1297 +000.1192 +00.0000 +00.0000 p Y Location -000.0299 -000.0401 +00.0000 +00.0000 Z Location -000.0105 -000.0417 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 15 36 -------------------------------------------------------------------------------- Step: 41 MM Cart Decimal Degree Construct Midpoint Actual Nominal Upper Tol. Lower Tol. 3-D Distance +009.8585 +000.0000 +00.0000 +00.0000 X Location +179.9795 +000.0000 +00.0000 +00.0000 Y Location +184.9126 +000.0000 +00.0000 +00.0000 Z Location +000.0045 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 37 32 -------------------------------------------------------------------------------- Step: 42 MM Cart Decimal Degree Construct Midpoint Actual Nominal Upper Tol. Lower Tol. 3-D Distance +010.6071 +000.0000 +00.0000 +00.0000 X Location +365.4534 +000.0000 +00.0000 +00.0000 Y Location +000.0014 +000.0000 +00.0000 +00.0000 Z Location -000.0305 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 33 38 -------------------------------------------------------------------------------- Step: 43 MM Cart Decimal Degree Construct Midpoint Actual Nominal Upper Tol. Lower Tol. 3-D Distance +010.0073 +000.0000 +00.0000 +00.0000 X Location +180.0530 +000.0000 +00.0000 +00.0000 Y Location -185.0052 +000.0000 +00.0000 +00.0000 Z Location -000.0658 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 34 39 -------------------------------------------------------------------------------- Step: 44 MM Cart Decimal Degree Construct Midpoint Actual Nominal Upper Tol. Lower Tol. 3-D Distance +010.1812 +000.0000 +00.0000 +00.0000 X Location -004.9609 +000.0000 +00.0000 +00.0000 Y Location -000.0304 +000.0000 +00.0000 +00.0000 Z Location -000.0050 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 35 40 -------------------------------------------------------------------------------- Step: 45 MM Cart Decimal Degree Construct XY Plane Comment: LINE between top and bottom pins for orign Line Actual Nominal Upper Tol. Lower Tol. p Angle -089.9886 -089.9791 +00.0000 +00.0000 p X Location +180.0162 +179.9897 +00.0000 +00.0000 p Y Location -000.0463 -000.0090 +00.0000 +00.0000 Z Location -000.0307 -000.0647 +00.0000 +00.0000 Straightness +000.0000 +00.0000 Features: 2Reference Feature(s): 41 43 -------------------------------------------------------------------------------- Step: 46 MM Cart Decimal Degree Construct XY Plane Comment: LINE between Left and Right pins for orign Line Actual Nominal Upper Tol. Lower Tol. p Angle +000.0049 +000.0022 +00.0000 +00.0000 p X Location +180.2462 +180.1295 +00.0000 +00.0000 p Y Location -000.0145 -000.0331 +00.0000 +00.0000 Z Location -000.0177 -000.0219 +00.0000 +00.0000 Straightness +000.0000 +00.0000 Features: 2Reference Feature(s): 42 44 -------------------------------------------------------------------------------- Step: 47 MM Cart Decimal Degree Construct Comment: INTERSECTION of two pin lines Intersect Actual Nominal Upper Tol. Lower Tol. p Angle 1 +270.0065 +090.0187 +00.0000 +00.0000 p X Location +180.0162 +179.9897 +00.0000 +00.0000 p Y Location -000.0146 -000.0332 +00.0000 +00.0000 Z Location -000.0242 -000.0433 +00.0000 +00.0000 1 of 2 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 46 45 -------------------------------------------------------------------------------- Step: 48 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero X Axis x Zero Y Axis At Actual Features: 1Reference Feature(s): 47 -------------------------------------------------------------------------------- Step: 49 MM Cart Decimal Degree Construct Align Actual Nominal Upper Tol. Lower Tol. Align Angle +090.0000 At Actual Features: 1Reference Feature(s): 41 -------------------------------------------------------------------------------- Step: 50 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -001.3964 +000.0000 +00.0000 +00.0000 Y Location +181.0517 +000.0000 +00.0000 +00.0000 Z Location -000.0055 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 51 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 50 -------------------------------------------------------------------------------- Step: 52 MM Cart Decimal Degree Measure XY Plane Comment: Top pin Line Actual Nominal Upper Tol. Lower Tol. p Angle -090.7070 -090.0000 +00.0000 +00.0000 X Location -001.7954 -001.7439 +00.0000 +00.0000 Y Location +180.0060 +180.0085 +00.0000 +00.0000 Z Location +000.0005 +000.0005 +00.0000 +00.0000 Straightness +000.0013 +00.0000 Lens: 1x Points: 11 Data Stream: No -------------------------------------------------------------------------------- Step: 53 MM Cart Decimal Degree Measure XY Plane Comment: Top pin right Line Actual Nominal Upper Tol. Lower Tol. p Angle +089.3025 +089.3074 +00.0000 +00.0000 X Location +001.6940 +001.7447 +00.0000 +00.0000 Y Location +180.0930 +180.0945 +00.0000 +00.0000 Z Location +000.0000 -000.0003 +00.0000 +00.0000 Straightness +000.0005 +00.0000 Lens: 1x Points: 8 Data Stream: No -------------------------------------------------------------------------------- Step: 54 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +179.1168 +000.0000 +00.0000 +00.0000 Y Location +001.2214 +000.0000 +00.0000 +00.0000 Z Location +000.0474 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 55 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 54 -------------------------------------------------------------------------------- Step: 56 MM Cart Decimal Degree Measure XY Plane Comment: RIGHT pin top side Line Actual Nominal Upper Tol. Lower Tol. p Angle -179.8489 -180.0000 +00.0000 +00.0000 X Location +180.2024 +180.2082 +00.0000 +00.0000 Y Location +001.6972 +001.6832 +00.0000 +00.0000 Z Location -000.0003 -000.0002 +00.0000 +00.0000 Straightness +000.0004 +00.0000 Lens: 1x Points: 8 Data Stream: No -------------------------------------------------------------------------------- Step: 57 MM Cart Decimal Degree Measure XY Plane Comment: RIGHT pin bottom Line Actual Nominal Upper Tol. Lower Tol. p Angle +000.1347 +000.0000 +00.0000 +00.0000 X Location +180.1029 +180.1014 +00.0000 +00.0000 Y Location -001.7880 -001.8004 +00.0000 +00.0000 Z Location -000.0018 -000.0003 +00.0000 +00.0000 Straightness +000.0005 +00.0000 Lens: 1x Points: 8 Data Stream: No -------------------------------------------------------------------------------- Step: 58 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +001.3437 +000.0000 +00.0000 +00.0000 Y Location -178.9151 +000.0000 +00.0000 +00.0000 Z Location -000.1010 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 59 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 58 -------------------------------------------------------------------------------- Step: 60 MM Cart Decimal Degree Measure XY Plane Comment: BOTTOM pin right side Line Actual Nominal Upper Tol. Lower Tol. p Angle +089.8660 +090.0000 +00.0000 +00.0000 X Location +001.7455 +001.7446 +00.0000 +00.0000 Y Location -179.9686 -179.9653 +00.0000 +00.0000 Z Location +000.0006 -000.0001 +00.0000 +00.0000 Straightness +000.0008 +00.0000 Lens: 1x Points: 7 Data Stream: No -------------------------------------------------------------------------------- Step: 61 MM Cart Decimal Degree Measure XY Plane Comment: BOTTOM pin left side Line Actual Nominal Upper Tol. Lower Tol. p Angle -090.1319 -090.0000 +00.0000 +00.0000 X Location -001.7420 -001.7434 +00.0000 +00.0000 Y Location -179.9794 -179.9771 +00.0000 +00.0000 Z Location -000.0024 -000.0004 +00.0000 +00.0000 Straightness +000.0006 +00.0000 Lens: 1x Points: 7 Data Stream: No -------------------------------------------------------------------------------- Step: 62 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -178.6688 +000.0000 +00.0000 +00.0000 Y Location -001.2769 +000.0000 +00.0000 +00.0000 Z Location +000.0050 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 63 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 62 -------------------------------------------------------------------------------- Step: 64 MM Cart Decimal Degree Measure XY Plane Comment: LEFT pin bottom side Line Actual Nominal Upper Tol. Lower Tol. p Angle -000.1061 +000.0000 +00.0000 +00.0000 X Location -179.6986 -179.7073 +00.0000 +00.0000 Y Location -001.7224 -001.6837 +00.0000 +00.0000 Z Location -000.0013 +000.0001 +00.0000 +00.0000 Straightness +000.0003 +00.0000 Lens: 1x Points: 7 Data Stream: No -------------------------------------------------------------------------------- Step: 65 MM Cart Decimal Degree Measure XY Plane Comment: LEFT pin top side Line Actual Nominal Upper Tol. Lower Tol. p Angle +179.8908 +180.0000 +00.0000 +00.0000 X Location -179.7305 -179.7409 +00.0000 +00.0000 Y Location +001.7619 +001.7998 +00.0000 +00.0000 Z Location -000.0018 -000.0009 +00.0000 +00.0000 Straightness +000.0007 +00.0000 Lens: 1x Points: 8 Data Stream: No -------------------------------------------------------------------------------- Step: 66 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -001.2280 +000.0000 +00.0000 +00.0000 Y Location +190.3930 +000.0000 +00.0000 +00.0000 Z Location +000.0411 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 67 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 66 -------------------------------------------------------------------------------- Step: 68 MM Cart Decimal Degree Measure XY Plane Comment: TOP outside pin left edge Line Actual Nominal Upper Tol. Lower Tol. p Angle -090.6902 -090.0000 +00.0000 +00.0000 X Location -001.6810 -001.6300 +00.0000 +00.0000 Y Location +190.6969 +190.6971 +00.0000 +00.0000 Z Location +000.0006 +000.0006 +00.0000 +00.0000 Straightness +000.0005 +00.0000 Lens: 1x Points: 11 Data Stream: No -------------------------------------------------------------------------------- Step: 69 MM Cart Decimal Degree Measure XY Plane Comment: TOP outside pin right edge Line Actual Nominal Upper Tol. Lower Tol. p Angle +089.3012 +090.0000 +00.0000 +00.0000 X Location +001.8049 +001.8566 +00.0000 +00.0000 Y Location +190.6510 +190.6511 +00.0000 +00.0000 Z Location +000.0036 +000.0007 +00.0000 +00.0000 Straightness +000.0009 +00.0000 Lens: 1x Points: 11 Data Stream: No -------------------------------------------------------------------------------- Step: 70 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +191.1588 +000.0000 +00.0000 +00.0000 Y Location +001.4061 +000.0000 +00.0000 +00.0000 Z Location +000.0081 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 71 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 70 -------------------------------------------------------------------------------- Step: 72 MM Cart Decimal Degree Measure XY Plane Comment: RIGHT outside pin top edge Line Actual Nominal Upper Tol. Lower Tol. p Angle -179.8193 -180.0000 +00.0000 +00.0000 X Location +191.6791 +191.6685 +00.0000 +00.0000 Y Location +001.7495 +001.7348 +00.0000 +00.0000 Z Location +000.0005 +000.0007 +00.0000 +00.0000 Straightness +000.0040 +00.0000 Lens: 1x Points: 15 Data Stream: No -------------------------------------------------------------------------------- Step: 73 MM Cart Decimal Degree Measure XY Plane Comment: RIGHT outside pin bottom edge Line Actual Nominal Upper Tol. Lower Tol. p Angle +000.1554 +000.0000 +00.0000 +00.0000 X Location +191.6567 +191.6503 +00.0000 +00.0000 Y Location -001.7343 -001.7489 +00.0000 +00.0000 Z Location +000.0005 -000.0007 +00.0000 +00.0000 Straightness +000.0013 +00.0000 Lens: 1x Points: 15 Data Stream: No -------------------------------------------------------------------------------- Step: 74 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +001.3847 +000.0000 +00.0000 +00.0000 Y Location -190.7568 +000.0000 +00.0000 +00.0000 Z Location -000.0466 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 75 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 74 -------------------------------------------------------------------------------- Step: 76 MM Cart Decimal Degree Measure XY Plane Comment: BOTTOM outside pin right edge Line Actual Nominal Upper Tol. Lower Tol. p Angle +089.8751 +090.0000 +00.0000 +00.0000 X Location +001.7404 +001.7370 +00.0000 +00.0000 Y Location -191.0104 -191.0100 +00.0000 +00.0000 Z Location +000.0005 +000.0004 +00.0000 +00.0000 Straightness +000.0008 +00.0000 Lens: 1x Points: 12 Data Stream: No -------------------------------------------------------------------------------- Step: 77 MM Cart Decimal Degree Measure XY Plane Comment: BOTTOM outside pin left edge Line Actual Nominal Upper Tol. Lower Tol. p Angle -090.1269 -090.0000 +00.0000 +00.0000 X Location -001.7461 -001.7494 +00.0000 +00.0000 Y Location -190.9279 -190.9274 +00.0000 +00.0000 Z Location +000.0020 +000.0003 +00.0000 +00.0000 Straightness +000.0005 +00.0000 Lens: 1x Points: 12 Data Stream: No -------------------------------------------------------------------------------- Step: 78 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -191.4310 +000.0000 +00.0000 +00.0000 Y Location -001.4772 +000.0000 +00.0000 +00.0000 Z Location +000.0116 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 79 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 78 -------------------------------------------------------------------------------- Step: 80 MM Cart Decimal Degree Measure XY Plane Comment: LEFT outside pin bottom edge Line Actual Nominal Upper Tol. Lower Tol. p Angle -000.1166 +000.0000 +00.0000 +00.0000 X Location -191.3526 -191.3606 +00.0000 +00.0000 Y Location -001.7210 -001.6809 +00.0000 +00.0000 Z Location +000.0004 -000.0001 +00.0000 +00.0000 Straightness +000.0015 +00.0000 Lens: 1x Points: 16 Data Stream: No -------------------------------------------------------------------------------- Step: 81 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -191.4118 +000.0000 +00.0000 +00.0000 Y Location +001.4178 +000.0000 +00.0000 +00.0000 Z Location +000.0027 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 82 MM Cart Decimal Degree Measure XY Plane Comment: LEFT outside pin top edge Line Actual Nominal Upper Tol. Lower Tol. p Angle +179.8800 +180.0000 +00.0000 +00.0000 X Location -191.4065 -191.4105 +00.0000 +00.0000 Y Location +001.7646 +001.8052 +00.0000 +00.0000 Z Location +000.0019 +000.0000 +00.0000 +00.0000 Straightness +000.0020 +00.0000 Lens: 1x Points: 16 Data Stream: No -------------------------------------------------------------------------------- Step: 83 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +020.5080 +000.0000 +00.0000 +00.0000 Y Location +154.5259 +000.0000 +00.0000 +00.0000 Z Location +007.8406 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 84 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 83 -------------------------------------------------------------------------------- Step: 85 MM Cart Decimal Degree Measure XY Plane Comment: 3mm hole #1 Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +003.0199 +003.0000 +00.0000 +00.0000 p X Location +020.5277 +020.5746 +00.0000 +00.0000 p Y Location +154.5302 +154.5409 +00.0000 +00.0000 Z Location +000.0004 -000.0001 +00.0000 +00.0000 p Roundness +000.0123 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 39 Data Stream: No -------------------------------------------------------------------------------- Step: 86 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +063.3491 +000.0000 +00.0000 +00.0000 Y Location +152.3536 +000.0000 +00.0000 +00.0000 Z Location -000.1707 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 87 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 86 -------------------------------------------------------------------------------- Step: 88 MM Cart Decimal Degree Measure XY Plane Comment: 3mm hole #2 Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +003.0225 +003.0000 +00.0000 +00.0000 p X Location +063.3185 +063.3660 +00.0000 +00.0000 p Y Location +152.2859 +152.2906 +00.0000 +00.0000 Z Location +000.0006 +000.0007 +00.0000 +00.0000 p Roundness +000.0105 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 40 Data Stream: No -------------------------------------------------------------------------------- Step: 89 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +095.1785 +000.0000 +00.0000 +00.0000 Y Location +123.6707 +000.0000 +00.0000 +00.0000 Z Location +000.5753 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 90 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 89 -------------------------------------------------------------------------------- Step: 91 MM Cart Decimal Degree Measure XY Plane Comment: 3mm hole #3 Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +003.0197 +003.0000 +00.0000 +00.0000 p X Location +095.1082 +095.1517 +00.0000 +00.0000 p Y Location +123.5738 +123.5733 +00.0000 +00.0000 Z Location +000.0003 +000.0001 +00.0000 +00.0000 p Roundness +000.0045 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 36 Data Stream: No -------------------------------------------------------------------------------- Step: 92 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +123.7359 +000.0000 +00.0000 +00.0000 Y Location +095.0648 +000.0000 +00.0000 +00.0000 Z Location -000.5231 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 93 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 92 -------------------------------------------------------------------------------- Step: 94 MM Cart Decimal Degree Measure XY Plane Comment: 3mm hole #4 Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +003.0236 +003.0000 +00.0000 +00.0000 p X Location +123.8987 +123.9383 +00.0000 +00.0000 p Y Location +094.7498 +094.7458 +00.0000 +00.0000 Z Location +000.0004 -000.0004 +00.0000 +00.0000 p Roundness +000.0068 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 36 Data Stream: No -------------------------------------------------------------------------------- Step: 95 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +152.5065 +000.0000 +00.0000 +00.0000 Y Location +062.9891 +000.0000 +00.0000 +00.0000 Z Location +000.3996 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 96 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 95 -------------------------------------------------------------------------------- Step: 97 MM Cart Decimal Degree Measure XY Plane Comment: 3mm hole #5 Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +003.0338 +003.0000 +00.0000 +00.0000 p X Location +152.5566 +152.5914 +00.0000 +00.0000 p Y Location +062.9074 +062.8994 +00.0000 +00.0000 Z Location +000.0004 +000.0004 +00.0000 +00.0000 p Roundness +000.0105 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 36 Data Stream: No -------------------------------------------------------------------------------- Step: 98 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +154.6610 +000.0000 +00.0000 +00.0000 Y Location +020.2108 +000.0000 +00.0000 +00.0000 Z Location -000.2361 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 99 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 98 -------------------------------------------------------------------------------- Step: 100 MM Cart Decimal Degree Measure XY Plane Comment: 3mm hole #6 Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +003.0190 +003.0000 +00.0000 +00.0000 p X Location +154.7647 +154.7940 +00.0000 +00.0000 p Y Location +020.1268 +020.1172 +00.0000 +00.0000 Z Location +000.0000 +000.0000 +00.0000 +00.0000 p Roundness +000.0140 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 36 Data Stream: No -------------------------------------------------------------------------------- Step: 101 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +154.6228 +000.0000 +00.0000 +00.0000 Y Location -020.4245 +000.0000 +00.0000 +00.0000 Z Location +000.3758 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 102 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 101 -------------------------------------------------------------------------------- Step: 103 MM Cart Decimal Degree Measure XY Plane Comment: 3mm hole #7 Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +003.0590 +003.0000 +00.0000 +00.0000 p X Location +154.7405 +154.7630 +00.0000 +00.0000 p Y Location -020.5943 -020.6053 +00.0000 +00.0000 Z Location +000.0003 -000.0004 +00.0000 +00.0000 p Roundness +000.0301 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 32 Data Stream: No -------------------------------------------------------------------------------- Step: 104 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +152.5389 +000.0000 +00.0000 +00.0000 Y Location -063.0878 +000.0000 +00.0000 +00.0000 Z Location -000.1043 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 105 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 104 -------------------------------------------------------------------------------- Step: 106 MM Cart Decimal Degree Measure XY Plane Comment: 3mm hole #8 Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +003.0132 +003.0000 +00.0000 +00.0000 p X Location +152.4902 +152.5077 +00.0000 +00.0000 p Y Location -063.3871 -063.3960 +00.0000 +00.0000 Z Location +000.0006 -000.0002 +00.0000 +00.0000 p Roundness +000.0130 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 36 Data Stream: No -------------------------------------------------------------------------------- Step: 107 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +123.7292 +000.0000 +00.0000 +00.0000 Y Location -094.9201 +000.0000 +00.0000 +00.0000 Z Location -000.0240 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 108 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 107 -------------------------------------------------------------------------------- Step: 109 MM Cart Decimal Degree Measure XY Plane Comment: 3mm hole #9 Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +003.0171 +003.0000 +00.0000 +00.0000 p X Location +123.7782 +123.7902 +00.0000 +00.0000 p Y Location -095.1863 -095.1905 +00.0000 +00.0000 Z Location +000.0006 -000.0007 +00.0000 +00.0000 p Roundness +000.0084 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 36 Data Stream: No -------------------------------------------------------------------------------- Step: 110 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +094.9526 +000.0000 +00.0000 +00.0000 Y Location -123.8879 +000.0000 +00.0000 +00.0000 Z Location +000.0080 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 111 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 110 -------------------------------------------------------------------------------- Step: 112 MM Cart Decimal Degree Measure XY Plane Comment: 3mm hole #10 Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +003.0013 +003.0000 +00.0000 +00.0000 p X Location +094.9555 +094.9636 +00.0000 +00.0000 p Y Location -123.9874 -123.9875 +00.0000 +00.0000 Z Location +000.0006 -000.0001 +00.0000 +00.0000 p Roundness +000.0401 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 35 Data Stream: No -------------------------------------------------------------------------------- Step: 113 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +062.9476 +000.0000 +00.0000 +00.0000 Y Location -152.5431 +000.0000 +00.0000 +00.0000 Z Location -000.0124 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 114 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 113 -------------------------------------------------------------------------------- Step: 115 MM Cart Decimal Degree Measure XY Plane Comment: 3mm hole #11 Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +003.0277 +003.0000 +00.0000 +00.0000 p X Location +063.1001 +063.1034 +00.0000 +00.0000 p Y Location -152.6498 -152.6455 +00.0000 +00.0000 Z Location +000.0006 +000.0006 +00.0000 +00.0000 p Roundness +000.0231 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 35 Data Stream: No -------------------------------------------------------------------------------- Step: 116 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +020.1621 +000.0000 +00.0000 +00.0000 Y Location -154.6535 +000.0000 +00.0000 +00.0000 Z Location +000.0534 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 117 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 116 -------------------------------------------------------------------------------- Step: 118 MM Cart Decimal Degree Measure XY Plane Comment: 3mm hole #12 Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +003.0151 +003.0000 +00.0000 +00.0000 p X Location +020.3310 +020.3343 +00.0000 +00.0000 p Y Location -154.8354 -154.8253 +00.0000 +00.0000 Z Location +000.0006 -000.0001 +00.0000 +00.0000 p Roundness +000.0111 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 36 Data Stream: No -------------------------------------------------------------------------------- Step: 119 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -020.5329 +000.0000 +00.0000 +00.0000 Y Location -154.5997 +000.0000 +00.0000 +00.0000 Z Location -000.1496 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 120 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 119 -------------------------------------------------------------------------------- Step: 121 MM Cart Decimal Degree Measure XY Plane Comment: 3mm hole #13 Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +003.0585 +003.0580 +00.0000 +00.0000 p X Location -020.4377 -020.4348 +00.0000 +00.0000 p Y Location -154.8033 -154.7872 +00.0000 +00.0000 Z Location +000.0007 +000.0001 +00.0000 +00.0000 p Roundness +000.0274 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 31 Data Stream: No -------------------------------------------------------------------------------- Step: 122 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -063.4333 +000.0000 +00.0000 +00.0000 Y Location -152.3128 +000.0000 +00.0000 +00.0000 Z Location +000.1766 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 123 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 122 -------------------------------------------------------------------------------- Step: 124 MM Cart Decimal Degree Measure XY Plane Comment: 3mm hole #14 Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +003.0140 +003.0000 +00.0000 +00.0000 p X Location -063.1844 -063.1810 +00.0000 +00.0000 p Y Location -152.5424 -152.5210 +00.0000 +00.0000 Z Location +000.0007 -000.0003 +00.0000 +00.0000 p Roundness +000.0059 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 36 Data Stream: No -------------------------------------------------------------------------------- Step: 125 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -095.1613 +000.0000 +00.0000 +00.0000 Y Location -123.6636 +000.0000 +00.0000 +00.0000 Z Location -000.0966 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 126 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 125 -------------------------------------------------------------------------------- Step: 127 MM Cart Decimal Degree Measure XY Plane Comment: 3mm hole #15 Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +003.0147 +003.0000 +00.0000 +00.0000 p X Location -094.9882 -094.9810 +00.0000 +00.0000 p Y Location -123.8496 -123.8232 +00.0000 +00.0000 Z Location +000.0007 +000.0000 +00.0000 +00.0000 p Roundness +000.0147 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 34 Data Stream: No -------------------------------------------------------------------------------- Step: 128 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -123.8274 +000.0000 +00.0000 +00.0000 Y Location -094.8907 +000.0000 +00.0000 +00.0000 Z Location -000.2763 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 129 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 128 -------------------------------------------------------------------------------- Step: 130 MM Cart Decimal Degree Measure XY Plane Comment: 3mm hole #16 Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +003.0300 +003.0000 +00.0000 +00.0000 p X Location -123.7733 -123.7620 +00.0000 +00.0000 p Y Location -095.0269 -094.9963 +00.0000 +00.0000 Z Location +000.0005 -000.0002 +00.0000 +00.0000 p Roundness +000.0120 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 36 Data Stream: No -------------------------------------------------------------------------------- Step: 131 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -152.6358 +000.0000 +00.0000 +00.0000 Y Location -062.9505 +000.0000 +00.0000 +00.0000 Z Location +000.3077 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 132 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 131 -------------------------------------------------------------------------------- Step: 133 MM Cart Decimal Degree Measure XY Plane Comment: 3mm hole #17 Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +003.0123 +003.0000 +00.0000 +00.0000 p X Location -152.4366 -152.4208 +00.0000 +00.0000 p Y Location -063.1804 -063.1458 +00.0000 +00.0000 Z Location +000.0008 +000.0003 +00.0000 +00.0000 p Roundness +000.0046 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 36 Data Stream: No -------------------------------------------------------------------------------- Step: 134 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -154.5905 +000.0000 +00.0000 +00.0000 Y Location -020.1810 +000.0000 +00.0000 +00.0000 Z Location +000.0450 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 135 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 134 -------------------------------------------------------------------------------- Step: 136 MM Cart Decimal Degree Measure XY Plane Comment: 3mm hole #18 Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +003.0087 +003.0000 +00.0000 +00.0000 p X Location -154.6298 -154.6077 +00.0000 +00.0000 p Y Location -020.3934 -020.3590 +00.0000 +00.0000 Z Location +000.0004 +000.0005 +00.0000 +00.0000 p Roundness +000.0071 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 36 Data Stream: No -------------------------------------------------------------------------------- Step: 137 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -154.6897 +000.0000 +00.0000 +00.0000 Y Location +020.5918 +000.0000 +00.0000 +00.0000 Z Location -000.3116 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 138 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 137 -------------------------------------------------------------------------------- Step: 139 MM Cart Decimal Degree Measure XY Plane Comment: 3mm hole #19 Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +003.0201 +003.0000 +00.0000 +00.0000 p X Location -154.6023 -154.5736 +00.0000 +00.0000 p Y Location +020.3606 +020.3949 +00.0000 +00.0000 Z Location +000.0005 -000.0001 +00.0000 +00.0000 p Roundness +000.0071 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 36 Data Stream: No -------------------------------------------------------------------------------- Step: 140 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -152.4353 +000.0000 +00.0000 +00.0000 Y Location +063.2709 +000.0000 +00.0000 +00.0000 Z Location +000.3220 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 141 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 140 -------------------------------------------------------------------------------- Step: 142 MM Cart Decimal Degree Measure XY Plane Comment: 3mm hole #20 Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +003.0069 +003.0000 +00.0000 +00.0000 p X Location -152.3625 -152.3280 +00.0000 +00.0000 p Y Location +063.1269 +063.1613 +00.0000 +00.0000 Z Location +000.0004 +000.0005 +00.0000 +00.0000 p Roundness +000.0133 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 36 Data Stream: No -------------------------------------------------------------------------------- Step: 143 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -123.7851 +000.0000 +00.0000 +00.0000 Y Location +095.0872 +000.0000 +00.0000 +00.0000 Z Location +000.0007 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 144 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 143 -------------------------------------------------------------------------------- Step: 145 MM Cart Decimal Degree Measure XY Plane Comment: 3mm hole #21 Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +003.0130 +003.0129 +00.0000 +00.0000 p X Location -123.6523 -123.6135 +00.0000 +00.0000 p Y Location +094.9339 +094.9647 +00.0000 +00.0000 Z Location +000.0003 +000.0004 +00.0000 +00.0000 p Roundness +000.0089 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 36 Data Stream: No -------------------------------------------------------------------------------- Step: 146 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -094.9648 +000.0000 +00.0000 +00.0000 Y Location +124.0002 +000.0000 +00.0000 +00.0000 Z Location +000.0343 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 147 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 146 -------------------------------------------------------------------------------- Step: 148 MM Cart Decimal Degree Measure XY Plane Comment: 3mm hole #22 Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +003.0055 +003.0000 +00.0000 +00.0000 p X Location -094.8299 -094.7862 +00.0000 +00.0000 p Y Location +123.7031 +123.7301 +00.0000 +00.0000 Z Location +000.0005 -000.0002 +00.0000 +00.0000 p Roundness +000.0102 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 36 Data Stream: No -------------------------------------------------------------------------------- Step: 149 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -063.0604 +000.0000 +00.0000 +00.0000 Y Location +152.5632 +000.0000 +00.0000 +00.0000 Z Location -000.0207 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 150 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 149 -------------------------------------------------------------------------------- Step: 151 MM Cart Decimal Degree Measure XY Plane Comment: 3mm hole #23 Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +003.0160 +003.0000 +00.0000 +00.0000 p X Location -062.9983 -062.9502 +00.0000 +00.0000 p Y Location +152.3603 +152.3835 +00.0000 +00.0000 Z Location +000.0007 -000.0007 +00.0000 +00.0000 p Roundness +000.0196 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 36 Data Stream: No -------------------------------------------------------------------------------- Step: 152 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -020.3543 +000.0000 +00.0000 +00.0000 Y Location +154.6727 +000.0000 +00.0000 +00.0000 Z Location +000.0137 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 153 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 152 -------------------------------------------------------------------------------- Step: 154 MM Cart Decimal Degree Measure XY Plane Comment: 3mm hole #24 Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +003.0151 +003.0000 +00.0000 +00.0000 p X Location -020.2037 -020.1559 +00.0000 +00.0000 p Y Location +154.5655 +154.5821 +00.0000 +00.0000 Z Location +000.0005 +000.0004 +00.0000 +00.0000 p Roundness +000.0062 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 36 Data Stream: No -------------------------------------------------------------------------------- Step: 155 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +026.3707 +000.0000 +00.0000 +00.0000 Y Location +169.6846 +000.0000 +00.0000 +00.0000 Z Location -003.4235 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 156 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 155 -------------------------------------------------------------------------------- Step: 157 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +026.8187 +000.0000 +00.0000 +00.0000 Y Location +170.2486 +000.0000 +00.0000 +00.0000 Z Location +000.0007 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 158 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +067.7222 +000.0000 +00.0000 +00.0000 Y Location +158.1088 +000.0000 +00.0000 +00.0000 Z Location +000.3032 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 159 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 158 -------------------------------------------------------------------------------- Step: 160 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +068.1299 +000.0000 +00.0000 +00.0000 Y Location +158.3818 +000.0000 +00.0000 +00.0000 Z Location +000.0006 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 161 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +105.6783 +000.0000 +00.0000 +00.0000 Y Location +135.5640 +000.0000 +00.0000 +00.0000 Z Location +000.0763 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 162 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 161 -------------------------------------------------------------------------------- Step: 163 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +106.3620 +000.0000 +00.0000 +00.0000 Y Location +135.7561 +000.0000 +00.0000 +00.0000 Z Location +000.0003 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 164 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +136.5682 +000.0000 +00.0000 +00.0000 Y Location +104.7776 +000.0000 +00.0000 +00.0000 Z Location -000.1534 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 165 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 164 -------------------------------------------------------------------------------- Step: 166 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +136.9412 +000.0000 +00.0000 +00.0000 Y Location +104.9045 +000.0000 +00.0000 +00.0000 Z Location +000.0007 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 167 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +159.0084 +000.0000 +00.0000 +00.0000 Y Location +065.8037 +000.0000 +00.0000 +00.0000 Z Location -000.1399 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 168 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 167 -------------------------------------------------------------------------------- Step: 169 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +159.4493 +000.0000 +00.0000 +00.0000 Y Location +065.8999 +000.0000 +00.0000 +00.0000 Z Location +000.0006 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 170 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +170.7929 +000.0000 +00.0000 +00.0000 Y Location +020.8986 +000.0000 +00.0000 +00.0000 Z Location +000.0537 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 171 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 170 -------------------------------------------------------------------------------- Step: 172 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +171.2659 +000.0000 +00.0000 +00.0000 Y Location +021.0254 +000.0000 +00.0000 +00.0000 Z Location +000.0004 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 173 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +170.6719 +000.0000 +00.0000 +00.0000 Y Location -022.9442 +000.0000 +00.0000 +00.0000 Z Location -000.1993 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 174 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 173 -------------------------------------------------------------------------------- Step: 175 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +171.1436 +000.0000 +00.0000 +00.0000 Y Location -022.9050 +000.0000 +00.0000 +00.0000 Z Location +000.0006 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 176 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +159.6505 +000.0000 +00.0000 +00.0000 Y Location -065.0337 +000.0000 +00.0000 +00.0000 Z Location -000.0349 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 177 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 176 -------------------------------------------------------------------------------- Step: 178 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +160.0028 +000.0000 +00.0000 +00.0000 Y Location -064.9462 +000.0000 +00.0000 +00.0000 Z Location +000.0005 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 179 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +137.2698 +000.0000 +00.0000 +00.0000 Y Location -104.2536 +000.0000 +00.0000 +00.0000 Z Location -000.0171 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 180 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 179 -------------------------------------------------------------------------------- Step: 181 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +137.7968 +000.0000 +00.0000 +00.0000 Y Location -104.0917 +000.0000 +00.0000 +00.0000 Z Location +000.0006 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 182 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +106.3824 +000.0000 +00.0000 +00.0000 Y Location -135.6124 +000.0000 +00.0000 +00.0000 Z Location -000.0056 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 183 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 182 -------------------------------------------------------------------------------- Step: 184 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +107.0529 +000.0000 +00.0000 +00.0000 Y Location -135.4973 +000.0000 +00.0000 +00.0000 Z Location +000.0003 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 185 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +066.5617 +000.0000 +00.0000 +00.0000 Y Location -158.8428 +000.0000 +00.0000 +00.0000 Z Location +000.1790 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 186 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 185 -------------------------------------------------------------------------------- Step: 187 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +066.8157 +000.0000 +00.0000 +00.0000 Y Location -159.1989 +000.0000 +00.0000 +00.0000 Z Location +000.0003 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 188 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +021.5900 +000.0000 +00.0000 +00.0000 Y Location -170.9490 +000.0000 +00.0000 +00.0000 Z Location -000.0610 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 189 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 188 -------------------------------------------------------------------------------- Step: 190 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +021.4018 +000.0000 +00.0000 +00.0000 Y Location -171.2808 +000.0000 +00.0000 +00.0000 Z Location +000.0003 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 191 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -025.1260 +000.0000 +00.0000 +00.0000 Y Location -170.3907 +000.0000 +00.0000 +00.0000 Z Location +000.1839 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 192 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 191 -------------------------------------------------------------------------------- Step: 193 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -067.3555 +000.0000 +00.0000 +00.0000 Y Location -158.5756 +000.0000 +00.0000 +00.0000 Z Location -000.0563 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 194 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 193 -------------------------------------------------------------------------------- Step: 195 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -067.7630 +000.0000 +00.0000 +00.0000 Y Location -158.5762 +000.0000 +00.0000 +00.0000 Z Location +000.0007 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 196 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -101.1456 +000.0000 +00.0000 +00.0000 Y Location -139.1068 +000.0000 +00.0000 +00.0000 Z Location +000.0084 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 197 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -101.6102 +000.0000 +00.0000 +00.0000 Y Location -139.2658 +000.0000 +00.0000 +00.0000 Z Location +000.0082 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 198 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -134.8681 +000.0000 +00.0000 +00.0000 Y Location -106.9411 +000.0000 +00.0000 +00.0000 Z Location -000.4277 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 199 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 198 -------------------------------------------------------------------------------- Step: 200 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -135.2442 +000.0000 +00.0000 +00.0000 Y Location -106.8795 +000.0000 +00.0000 +00.0000 Z Location -000.0001 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 201 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -157.4310 +000.0000 +00.0000 +00.0000 Y Location -069.2029 +000.0000 +00.0000 +00.0000 Z Location -004.7106 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 202 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 201 -------------------------------------------------------------------------------- Step: 203 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -158.0507 +000.0000 +00.0000 +00.0000 Y Location -069.0754 +000.0000 +00.0000 +00.0000 Z Location +000.0001 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 204 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -170.5979 +000.0000 +00.0000 +00.0000 Y Location -023.5585 +000.0000 +00.0000 +00.0000 Z Location -000.0257 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 205 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 204 -------------------------------------------------------------------------------- Step: 206 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -170.8551 +000.0000 +00.0000 +00.0000 Y Location -023.7205 +000.0000 +00.0000 +00.0000 Z Location +000.0004 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 207 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -170.5887 +000.0000 +00.0000 +00.0000 Y Location +022.6388 +000.0000 +00.0000 +00.0000 Z Location +005.1261 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 208 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 207 -------------------------------------------------------------------------------- Step: 209 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -170.9170 +000.0000 +00.0000 +00.0000 Y Location +023.1387 +000.0000 +00.0000 +00.0000 Z Location +000.0006 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 210 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -158.7632 +000.0000 +00.0000 +00.0000 Y Location +066.5519 +000.0000 +00.0000 +00.0000 Z Location -000.3689 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 211 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 210 -------------------------------------------------------------------------------- Step: 212 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -158.7849 +000.0000 +00.0000 +00.0000 Y Location +067.2139 +000.0000 +00.0000 +00.0000 Z Location +000.0005 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 213 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -134.5720 +000.0000 +00.0000 +00.0000 Y Location +107.1252 +000.0000 +00.0000 +00.0000 Z Location +000.2316 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 214 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 213 -------------------------------------------------------------------------------- Step: 215 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -134.5218 +000.0000 +00.0000 +00.0000 Y Location +107.8221 +000.0000 +00.0000 +00.0000 Z Location +000.0004 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 216 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -103.8171 +000.0000 +00.0000 +00.0000 Y Location +137.0717 +000.0000 +00.0000 +00.0000 Z Location +000.1587 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 217 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 216 -------------------------------------------------------------------------------- Step: 218 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -103.3915 +000.0000 +00.0000 +00.0000 Y Location +137.9580 +000.0000 +00.0000 +00.0000 Z Location +000.0007 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 219 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -065.2145 +000.0000 +00.0000 +00.0000 Y Location +158.9299 +000.0000 +00.0000 +00.0000 Z Location -000.2975 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 220 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 219 -------------------------------------------------------------------------------- Step: 221 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -065.0301 +000.0000 +00.0000 +00.0000 Y Location +159.6577 +000.0000 +00.0000 +00.0000 Z Location +000.0006 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 222 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -021.8801 +000.0000 +00.0000 +00.0000 Y Location +170.5584 +000.0000 +00.0000 +00.0000 Z Location +000.4306 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 223 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 222 -------------------------------------------------------------------------------- Step: 224 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -021.8667 +000.0000 +00.0000 +00.0000 Y Location +170.9771 +000.0000 +00.0000 +00.0000 Z Location +000.0005 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 225 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +044.5761 +000.0000 +00.0000 +00.0000 Y Location +141.8761 +000.0000 +00.0000 +00.0000 Z Location +000.0541 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 226 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 225 -------------------------------------------------------------------------------- Step: 227 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +045.0886 +000.0000 +00.0000 +00.0000 Y Location +141.4314 +000.0000 +00.0000 +00.0000 Z Location +000.0004 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 228 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +108.4301 +000.0000 +00.0000 +00.0000 Y Location +101.9595 +000.0000 +00.0000 +00.0000 Z Location -000.1835 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 229 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 228 -------------------------------------------------------------------------------- Step: 230 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +108.3534 +000.0000 +00.0000 +00.0000 Y Location +101.3721 +000.0000 +00.0000 +00.0000 Z Location +000.0004 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 231 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +145.1945 +000.0000 +00.0000 +00.0000 Y Location +032.8690 +000.0000 +00.0000 +00.0000 Z Location +000.1067 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 232 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 231 -------------------------------------------------------------------------------- Step: 233 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +144.9132 +000.0000 +00.0000 +00.0000 Y Location +032.6544 +000.0000 +00.0000 +00.0000 Z Location +000.0007 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 234 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +143.2555 +000.0000 +00.0000 +00.0000 Y Location -041.4501 +000.0000 +00.0000 +00.0000 Z Location -000.2453 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 235 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 234 -------------------------------------------------------------------------------- Step: 236 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +142.8335 +000.0000 +00.0000 +00.0000 Y Location -041.0729 +000.0000 +00.0000 +00.0000 Z Location +000.0005 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 237 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +102.0058 +000.0000 +00.0000 +00.0000 Y Location -108.9368 +000.0000 +00.0000 +00.0000 Z Location +000.0208 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 238 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 237 -------------------------------------------------------------------------------- Step: 239 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +101.2784 +000.0000 +00.0000 +00.0000 Y Location -108.8518 +000.0000 +00.0000 +00.0000 Z Location +000.0007 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 240 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +036.8126 +000.0000 +00.0000 +00.0000 Y Location -144.2583 +000.0000 +00.0000 +00.0000 Z Location -000.0623 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 241 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 240 -------------------------------------------------------------------------------- Step: 242 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +036.3876 +000.0000 +00.0000 +00.0000 Y Location -144.1031 +000.0000 +00.0000 +00.0000 Z Location +000.0004 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 243 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -042.3354 +000.0000 +00.0000 +00.0000 Y Location -142.7422 +000.0000 +00.0000 +00.0000 Z Location +000.2651 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 244 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 243 -------------------------------------------------------------------------------- Step: 245 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -042.6024 +000.0000 +00.0000 +00.0000 Y Location -142.3271 +000.0000 +00.0000 +00.0000 Z Location +000.0003 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 246 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -103.5347 +000.0000 +00.0000 +00.0000 Y Location -106.9988 +000.0000 +00.0000 +00.0000 Z Location -000.0231 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 247 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 246 -------------------------------------------------------------------------------- Step: 248 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -102.7773 +000.0000 +00.0000 +00.0000 Y Location -107.1967 +000.0000 +00.0000 +00.0000 Z Location -000.0001 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 249 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -144.0114 +000.0000 +00.0000 +00.0000 Y Location -037.8994 +000.0000 +00.0000 +00.0000 Z Location -000.0403 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 250 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 249 -------------------------------------------------------------------------------- Step: 251 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -143.7215 +000.0000 +00.0000 +00.0000 Y Location -037.4524 +000.0000 +00.0000 +00.0000 Z Location +000.0003 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 252 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -143.8353 +000.0000 +00.0000 +00.0000 Y Location +037.4934 +000.0000 +00.0000 +00.0000 Z Location -000.1277 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 253 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 252 -------------------------------------------------------------------------------- Step: 254 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -143.6308 +000.0000 +00.0000 +00.0000 Y Location +037.2390 +000.0000 +00.0000 +00.0000 Z Location +000.0005 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 255 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -108.0380 +000.0000 +00.0000 +00.0000 Y Location +102.1166 +000.0000 +00.0000 +00.0000 Z Location +000.1488 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 256 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 255 -------------------------------------------------------------------------------- Step: 257 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -107.6401 +000.0000 +00.0000 +00.0000 Y Location +102.1295 +000.0000 +00.0000 +00.0000 Z Location +000.0006 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 258 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -039.1855 +000.0000 +00.0000 +00.0000 Y Location +143.4253 +000.0000 +00.0000 +00.0000 Z Location +000.1007 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 259 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 258 -------------------------------------------------------------------------------- Step: 260 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -038.7474 +000.0000 +00.0000 +00.0000 Y Location +143.3529 +000.0000 +00.0000 +00.0000 Z Location +000.0005 +000.0000 +00.0000 +00.0000 Locate Point True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 261 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -003.3946 +000.0000 +00.0000 +00.0000 Y Location +180.0439 +000.0000 +00.0000 +00.0000 Z Location +001.7656 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 262 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 261 -------------------------------------------------------------------------------- Step: 263 MM Cart Decimal Degree Measure XY Plane Comment: TOP 6.5 hole radius Circle Actual Nominal Upper Tol. Lower Tol. p Radius +003.2710 +003.2500 +00.0000 +00.0000 p X Location +000.0757 +000.1189 +00.0000 +00.0000 p Y Location +180.0400 +180.0521 +00.0000 +00.0000 Z Location +000.0005 -000.0005 +00.0000 +00.0000 p Roundness +000.0031 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 11 Data Stream: No -------------------------------------------------------------------------------- Step: 264 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +003.5971 +000.0000 +00.0000 +00.0000 Y Location +180.0438 +000.0000 +00.0000 +00.0000 Z Location -000.0307 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 265 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 264 -------------------------------------------------------------------------------- Step: 266 MM Cart Decimal Degree Measure XY Plane Comment: TOP 6.5mm hole radius Circle Actual Nominal Upper Tol. Lower Tol. p Radius +003.2662 +003.2500 +00.0000 +00.0000 p X Location +000.0499 +000.1030 +00.0000 +00.0000 p Y Location +180.0497 +180.0640 +00.0000 +00.0000 Z Location +000.0006 +000.0004 +00.0000 +00.0000 p Roundness +000.0028 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 11 Data Stream: No -------------------------------------------------------------------------------- Step: 267 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +180.0699 +000.0000 +00.0000 +00.0000 Y Location +003.3553 +000.0000 +00.0000 +00.0000 Z Location -000.1651 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 268 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 267 -------------------------------------------------------------------------------- Step: 269 MM Cart Decimal Degree Measure XY Plane Comment: RIGHT 6.5mm hole radius Circle Actual Nominal Upper Tol. Lower Tol. p Radius +003.2372 +003.2500 +00.0000 +00.0000 p X Location +180.0172 +180.0418 +00.0000 +00.0000 p Y Location -000.0028 -000.0172 +00.0000 +00.0000 Z Location +000.0007 +000.0006 +00.0000 +00.0000 p Roundness +000.0037 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 13 Data Stream: No -------------------------------------------------------------------------------- Step: 270 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +180.0622 +000.0000 +00.0000 +00.0000 Y Location -003.5207 +000.0000 +00.0000 +00.0000 Z Location +000.1131 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 271 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 270 -------------------------------------------------------------------------------- Step: 272 MM Cart Decimal Degree Measure XY Plane Comment: RIGHT 6.5mm hole radius Circle Actual Nominal Upper Tol. Lower Tol. p Radius +003.2478 +003.2500 +00.0000 +00.0000 p X Location +180.0272 +180.0492 +00.0000 +00.0000 p Y Location -000.0334 -000.0304 +00.0000 +00.0000 Z Location +000.0006 -000.0003 +00.0000 +00.0000 p Roundness +000.0110 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 14 Data Stream: No -------------------------------------------------------------------------------- Step: 273 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location +003.3796 +000.0000 +00.0000 +00.0000 Y Location -180.0528 +000.0000 +00.0000 +00.0000 Z Location -000.0806 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 274 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 273 -------------------------------------------------------------------------------- Step: 275 MM Cart Decimal Degree Measure XY Plane Comment: BOTTOM 6.5mm hole radius Circle Actual Nominal Upper Tol. Lower Tol. p Radius +003.2678 +003.2500 +00.0000 +00.0000 p X Location -000.0188 -000.0181 +00.0000 +00.0000 p Y Location -179.9957 -179.9833 +00.0000 +00.0000 Z Location +000.0007 +000.0003 +00.0000 +00.0000 p Roundness +000.0032 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 12 Data Stream: No -------------------------------------------------------------------------------- Step: 276 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -003.6231 +000.0000 +00.0000 +00.0000 Y Location -180.0476 +000.0000 +00.0000 +00.0000 Z Location -000.1059 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 277 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 276 -------------------------------------------------------------------------------- Step: 278 MM Cart Decimal Degree Measure XY Plane Comment: BOTTOM 6.5mm hole radius Circle Actual Nominal Upper Tol. Lower Tol. p Radius +003.2542 +003.2500 +00.0000 +00.0000 p X Location -000.0102 -000.0114 +00.0000 +00.0000 p Y Location -180.0103 -179.9971 +00.0000 +00.0000 Z Location +000.0006 +000.0004 +00.0000 +00.0000 p Roundness +000.0087 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 12 Data Stream: No -------------------------------------------------------------------------------- Step: 279 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -180.1110 +000.0000 +00.0000 +00.0000 Y Location -003.2966 +000.0000 +00.0000 +00.0000 Z Location -000.0233 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 280 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 279 -------------------------------------------------------------------------------- Step: 281 MM Cart Decimal Degree Measure XY Plane Comment: LEFT 6.5mm hole radius Circle Actual Nominal Upper Tol. Lower Tol. p Radius +003.2554 +003.2500 +00.0000 +00.0000 p X Location -180.0045 -179.9794 +00.0000 +00.0000 p Y Location +000.0562 +000.0959 +00.0000 +00.0000 Z Location +000.0004 -000.0005 +00.0000 +00.0000 p Roundness +000.0084 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 14 Data Stream: No -------------------------------------------------------------------------------- Step: 282 MM Cart Decimal Degree Measure Point Actual Nominal Upper Tol. Lower Tol. X Location -179.9720 +000.0000 +00.0000 +00.0000 Y Location +003.4747 +000.0000 +00.0000 +00.0000 Z Location -000.1116 +000.0000 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 1 Data Stream: No -------------------------------------------------------------------------------- Step: 283 MM Cart Decimal Degree Construct Origin Actual Nominal Upper Tol. Lower Tol. x Zero Z Axis At Actual Features: 1Reference Feature(s): 282 -------------------------------------------------------------------------------- Step: 284 MM Cart Decimal Degree Measure XY Plane Comment: LEFT 6.5mm hole radius Circle Actual Nominal Upper Tol. Lower Tol. p Radius +003.2589 +003.2500 +00.0000 +00.0000 p X Location -180.0148 -179.9901 +00.0000 +00.0000 p Y Location +000.0529 +000.0913 +00.0000 +00.0000 Z Location +000.0005 +000.0003 +00.0000 +00.0000 p Roundness +000.0080 +00.0000 True Position Tolerance +00.0000 RFS Lens: 1x Points: 14 Data Stream: No -------------------------------------------------------------------------------- Step: 285 MM Cart Decimal Degree Construct XY Plane Comment: TOP 6.5mm hole Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +006.5136 +006.5000 +00.0000 +00.0000 p X Location +000.0601 +000.0000 +00.0000 +00.0000 p Y Location +180.0444 +180.0000 +00.0000 +00.0000 Z Location +000.3893 +000.3730 +00.0000 +00.0000 p Roundness +000.0080 +00.0000 True Position Tolerance +00.0000 RFS Features: 2 CompositeReference Feature(s): 266 263 -------------------------------------------------------------------------------- Step: 286 MM Cart Decimal Degree Construct XY Plane Comment: RIGHT 6.5mm hole Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +006.5117 +006.5000 +00.0000 +00.0000 p X Location +180.0219 +180.0000 +00.0000 +00.0000 p Y Location -000.0241 +000.0000 +00.0000 +00.0000 Z Location +000.2676 +000.2390 +00.0000 +00.0000 p Roundness +000.0165 +00.0000 True Position Tolerance +00.0000 RFS Features: 2 CompositeReference Feature(s): 272 269 -------------------------------------------------------------------------------- Step: 287 MM Cart Decimal Degree Construct XY Plane Comment: BOTTOM 6.5mm hole Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +006.5142 +006.5000 +00.0000 +00.0000 p X Location -000.0073 +000.0000 +00.0000 +00.0000 p Y Location -180.0032 -180.0000 +00.0000 +00.0000 Z Location +000.1885 +000.1605 +00.0000 +00.0000 p Roundness +000.0145 +00.0000 True Position Tolerance +00.0000 RFS Features: 2 CompositeReference Feature(s): 275 278 -------------------------------------------------------------------------------- Step: 288 MM Cart Decimal Degree Construct XY Plane Comment: LEFT 6.5mm hole Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +006.5113 +006.5000 +00.0000 +00.0000 p X Location -180.0096 -180.0000 +00.0000 +00.0000 p Y Location +000.0565 +000.0000 +00.0000 +00.0000 Z Location +000.0562 +000.0465 +00.0000 +00.0000 p Roundness +000.0137 +00.0000 True Position Tolerance +00.0000 RFS Features: 2 CompositeReference Feature(s): 284 281 -------------------------------------------------------------------------------- Step: 289 MM Cart Decimal Degree Construct XY Plane Comment: Circle Diameter thru 6.5mm holes Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +360.0398 +360.0000 +00.0000 +00.0000 p X Location +000.0063 +000.0000 +00.0000 +00.0000 p Y Location +000.0209 +000.0000 +00.0000 +00.0000 Z Location +000.2249 +000.2221 +00.0000 +00.0000 p Roundness +000.0205 +00.0000 True Position Tolerance +00.0000 RFS Features: 4 CompositeReference Feature(s): 285 286 287 288 -------------------------------------------------------------------------------- Step: 290 MM Cart Decimal Degree Construct XY Plane Comment: * Ring OD * Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +345.0030 +345.2400 +00.0000 +00.0000 p X Location +000.0967 +000.0000 +00.0000 +00.0000 p Y Location -000.0926 +000.0000 +00.0000 +00.0000 Z Location -002.0259 -002.0164 +00.0000 +00.0000 p Roundness +000.2085 +00.0000 True Position Tolerance +00.0000 RFS Features: 23 CompositeReference Feature(s): 157 160 163 166 169 172 175 178 181 184 187 190 195 197 200 203 206 209 212 215 218 221 224 -------------------------------------------------------------------------------- Step: 291 MM Cart Decimal Degree Construct XY Plane Comment: * Ring ID * Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +297.0691 +296.7600 +00.0000 +00.0000 p X Location +000.0751 +000.0981 +00.0000 +00.0000 p Y Location -000.0574 -000.0451 +00.0000 +00.0000 Z Location -001.4961 -001.5085 +00.0000 +00.0000 p Roundness +000.3814 +00.0000 True Position Tolerance +00.0000 RFS Features: 12 CompositeReference Feature(s): 225 230 233 236 239 242 245 248 251 254 257 260 -------------------------------------------------------------------------------- Step: 292 MM Cart Decimal Degree Construct XY Plane Comment: Circle Diameter Thru Outside ring of 3mm HOLES Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +330.0433 +330.0000 +00.0000 +00.0000 p X Location +000.0719 +000.0000 +00.0000 +00.0000 p Y Location -000.1182 +000.0000 +00.0000 +00.0000 Z Location +001.6754 +001.6593 +00.0000 +00.0000 p Roundness +003.0820 +00.0000 True Position Tolerance +00.0000 RFS Features: 8 CompositeReference Feature(s): 88 97 106 115 124 133 151 142 -------------------------------------------------------------------------------- Step: 293 MM Cart Decimal Degree Construct XY Plane Comment: Circle Diameter thru Inside ring of 3mm HOLES Circle Actual Nominal Upper Tol. Lower Tol. p Diameter +312.0342 +312.0000 +00.0000 +00.0000 p X Location +000.0636 +000.0000 +00.0000 +00.0000 p Y Location -000.1374 +000.0000 +00.0000 +00.0000 Z Location +001.6459 +001.6368 +00.0000 +00.0000 p Roundness +000.0200 +00.0000 True Position Tolerance +00.0000 RFS Features: 16Reference Feature(s): 85 91 94 100 103 109 112 118 121 127 130 136 154 148 145 139 -------------------------------------------------------------------------------- Step: 294 MM Cart Decimal Degree Construct XY Plane Comment: Angle 3mm hole #1 Line Actual Nominal Upper Tol. Lower Tol. p Sup. Angle +082.4332 +082.5000 +00.0000 +00.0000 X Location +010.2638 +010.2875 +00.0000 +00.0000 Y Location +077.2651 +077.2708 +00.0000 +00.0000 Z Location -002.4961 -002.4811 +00.0000 +00.0000 Straightness +000.0000 +00.0000 Features: 2Reference Feature(s): 85 47 -------------------------------------------------------------------------------- Step: 295 MM Cart Decimal Degree Construct XY Plane Comment: ANGLE 3mm hole #2 Line Actual Nominal Upper Tol. Lower Tol. p Sup. Angle +067.4231 +067.5000 +00.0000 +00.0000 X Location +031.6593 +031.6828 +00.0000 +00.0000 Y Location +076.1429 +076.1459 +00.0000 +00.0000 Z Location -002.5813 -002.5821 +00.0000 +00.0000 Straightness +000.0000 +00.0000 Features: 2Reference Feature(s): 88 47 -------------------------------------------------------------------------------- Step: 296 MM Cart Decimal Degree Construct XY Plane Comment: ANGLE 3mm hole #3 Line Actual Nominal Upper Tol. Lower Tol. p Sup. Angle +052.4164 +052.5000 +00.0000 +00.0000 X Location +047.5541 +047.5756 +00.0000 +00.0000 Y Location +061.7869 +061.7874 +00.0000 +00.0000 Z Location -002.2938 -002.2834 +00.0000 +00.0000 Straightness +000.0000 +00.0000 Features: 2Reference Feature(s): 91 47 -------------------------------------------------------------------------------- Step: 297 MM Cart Decimal Degree Construct XY Plane Comment: ANGLE 3mm hole #4 Line Actual Nominal Upper Tol. Lower Tol. p Sup. Angle +037.4064 +037.5000 +00.0000 +00.0000 X Location +061.9493 +061.9692 +00.0000 +00.0000 Y Location +047.3749 +047.3736 +00.0000 +00.0000 Z Location -002.5553 -002.5431 +00.0000 +00.0000 Straightness +000.0000 +00.0000 Features: 2Reference Feature(s): 94 47 -------------------------------------------------------------------------------- Step: 298 MM Cart Decimal Degree Construct XY Plane Comment: Angle 3mm hole #5 Line Actual Nominal Upper Tol. Lower Tol. p Sup. Angle +022.4090 +022.5000 +00.0000 +00.0000 X Location +076.2783 +076.2956 +00.0000 +00.0000 Y Location +031.4537 +031.4504 +00.0000 +00.0000 Z Location -002.3556 -002.3469 +00.0000 +00.0000 Straightness +000.0000 +00.0000 Features: 2Reference Feature(s): 97 47 -------------------------------------------------------------------------------- Step: 299 MM Cart Decimal Degree Construct XY Plane Comment: Angle 3mm hole #6 Line Actual Nominal Upper Tol. Lower Tol. p Sup. Angle +007.4096 +007.5000 +00.0000 +00.0000 X Location +077.3824 +077.3969 +00.0000 +00.0000 Y Location +010.0634 +010.0592 +00.0000 +00.0000 Z Location -002.4738 -002.4634 +00.0000 +00.0000 Straightness +000.0000 +00.0000 Features: 2Reference Feature(s): 100 47 -------------------------------------------------------------------------------- Step: 300 MM Cart Decimal Degree Construct XY Plane Comment: Angle 3mm hole #7 Line Actual Nominal Upper Tol. Lower Tol. p Sup. Angle +352.4752 +352.5000 +00.0000 +00.0000 X Location +077.3114 +077.3055 +00.0000 +00.0000 Y Location -010.2122 -010.2122 +00.0000 +00.0000 Z Location -002.2859 -002.2749 +00.0000 +00.0000 Straightness +000.0000 +00.0000 Features: 2Reference Feature(s): 101 47 -------------------------------------------------------------------------------- Step: 301 MM Cart Decimal Degree Construct XY Plane Comment: Angle 3mm hole #8 Line Actual Nominal Upper Tol. Lower Tol. p Sup. Angle +337.4283 +337.5000 +00.0000 +00.0000 X Location +076.2451 +076.2536 +00.0000 +00.0000 Y Location -031.6936 -031.6977 +00.0000 +00.0000 Z Location -002.3378 -002.3324 +00.0000 +00.0000 Straightness +000.0000 +00.0000 Features: 2Reference Feature(s): 106 47 -------------------------------------------------------------------------------- Step: 302 MM Cart Decimal Degree Construct XY Plane Comment: Angle 3mm hole #9 Line Actual Nominal Upper Tol. Lower Tol. p Sup. Angle +322.4394 +322.5000 +00.0000 +00.0000 X Location +061.8891 +061.8952 +00.0000 +00.0000 Y Location -047.5932 -047.5954 +00.0000 +00.0000 Z Location -002.3498 -002.3496 +00.0000 +00.0000 Straightness +000.0000 +00.0000 Features: 2Reference Feature(s): 109 47 -------------------------------------------------------------------------------- Step: 303 MM Cart Decimal Degree Construct XY Plane Comment: Angle 3mm hole #10 Line Actual Nominal Upper Tol. Lower Tol. p Sup. Angle +307.4466 +307.5000 +00.0000 +00.0000 X Location +047.4778 +047.4818 +00.0000 +00.0000 Y Location -061.9937 -061.9936 +00.0000 +00.0000 Z Location -002.3458 -002.3399 +00.0000 +00.0000 Straightness +000.0000 +00.0000 Features: 2Reference Feature(s): 112 47 -------------------------------------------------------------------------------- Step: 304 MM Cart Decimal Degree Construct XY Plane Comment: Angle 3mm hole #11 Line Actual Nominal Upper Tol. Lower Tol. p Sup. Angle +292.4585 +292.5000 +00.0000 +00.0000 X Location +031.5500 +031.5521 +00.0000 +00.0000 Y Location -076.3249 -076.3230 +00.0000 +00.0000 Z Location -002.3521 -002.3479 +00.0000 +00.0000 Straightness +000.0000 +00.0000 Features: 2Reference Feature(s): 115 47 -------------------------------------------------------------------------------- Step: 305 MM Cart Decimal Degree Construct XY Plane Comment: Angle 3mm hole #12 Line Actual Nominal Upper Tol. Lower Tol. p Sup. Angle +277.4805 +277.5000 +00.0000 +00.0000 X Location +010.1655 +010.1672 +00.0000 +00.0000 Y Location -077.4177 -077.4128 +00.0000 +00.0000 Z Location -002.3253 -002.3096 +00.0000 +00.0000 Straightness +000.0000 +00.0000 Features: 2Reference Feature(s): 118 47 -------------------------------------------------------------------------------- Step: 306 MM Cart Decimal Degree Construct XY Plane Comment: Angle 3mm hole #13 Line Actual Nominal Upper Tol. Lower Tol. p Sup. Angle +262.4791 +262.5000 +00.0000 +00.0000 X Location -010.2188 -010.2172 +00.0000 +00.0000 Y Location -077.4016 -077.3938 +00.0000 +00.0000 Z Location -002.4001 -002.4109 +00.0000 +00.0000 Straightness +000.0000 +00.0000 Features: 2Reference Feature(s): 121 47 -------------------------------------------------------------------------------- Step: 307 MM Cart Decimal Degree Construct XY Plane Comment: Angle 3mm hole #14 Line Actual Nominal Upper Tol. Lower Tol. p Sup. Angle +247.5002 +247.5000 +00.0000 +00.0000 X Location -031.5922 -031.5905 +00.0000 +00.0000 Y Location -076.2712 -076.2611 +00.0000 +00.0000 Z Location -002.3118 -002.3029 +00.0000 +00.0000 Straightness +000.0000 +00.0000 Features: 2Reference Feature(s): 124 47 -------------------------------------------------------------------------------- Step: 308 MM Cart Decimal Degree Construct XY Plane Comment: Angle 3mm hole #15 Line Actual Nominal Upper Tol. Lower Tol. p Sup. Angle +232.5131 +232.5000 +00.0000 +00.0000 X Location -047.4941 -047.4908 +00.0000 +00.0000 Y Location -061.9248 -061.9115 +00.0000 +00.0000 Z Location -002.3601 -002.3416 +00.0000 +00.0000 Straightness +000.0000 +00.0000 Features: 2Reference Feature(s): 127 47 -------------------------------------------------------------------------------- Step: 309 MM Cart Decimal Degree Construct XY Plane Comment: Angle 3mm hole #16 Line Actual Nominal Upper Tol. Lower Tol. p Sup. Angle +217.5153 +217.5000 +00.0000 +00.0000 X Location -061.8866 -061.8812 +00.0000 +00.0000 Y Location -047.5135 -047.4988 +00.0000 +00.0000 Z Location -002.4983 -002.4861 +00.0000 +00.0000 Straightness +000.0000 +00.0000 Features: 2Reference Feature(s): 130 47 -------------------------------------------------------------------------------- Step: 310 MM Cart Decimal Degree Construct XY Plane Comment: Angle 3mm hole #17 Line Actual Nominal Upper Tol. Lower Tol. p Sup. Angle +202.5125 +202.5000 +00.0000 +00.0000 X Location -076.2183 -076.2105 +00.0000 +00.0000 Y Location -031.5902 -031.5735 +00.0000 +00.0000 Z Location -002.3443 -002.3366 +00.0000 +00.0000 Straightness +000.0000 +00.0000 Features: 2Reference Feature(s): 47 133 -------------------------------------------------------------------------------- Step: 311 MM Cart Decimal Degree Construct XY Plane Comment: ANGLE 3mm hole #18 Line Actual Nominal Upper Tol. Lower Tol. p Angle -172.4869 -172.5000 +00.0000 +00.0000 X Location -077.3149 -077.3043 +00.0000 +00.0000 Y Location -010.1967 -010.1795 +00.0000 +00.0000 Z Location -002.3221 -002.3059 +00.0000 +00.0000 Straightness +000.0000 +00.0000 Features: 2Reference Feature(s): 47 136 -------------------------------------------------------------------------------- Step: 312 MM Cart Decimal Degree Construct XY Plane Comment: ANGLE 3mm hole #19 Line Actual Nominal Upper Tol. Lower Tol. p Angle +172.4975 +172.5000 +00.0000 +00.0000 X Location -077.3011 -077.2873 +00.0000 +00.0000 Y Location +010.1803 +010.1974 +00.0000 +00.0000 Z Location -002.4778 -002.4679 +00.0000 +00.0000 Straightness +000.0000 +00.0000 Features: 2Reference Feature(s): 47 139 -------------------------------------------------------------------------------- Step: 313 MM Cart Decimal Degree Construct XY Plane Comment: ANGLE 3mm hole #20 Line Actual Nominal Upper Tol. Lower Tol. p Angle +157.4948 +157.5000 +00.0000 +00.0000 X Location -076.1813 -076.1645 +00.0000 +00.0000 Y Location +031.5635 +031.5802 +00.0000 +00.0000 Z Location -002.3168 -002.3096 +00.0000 +00.0000 Straightness +000.0000 +00.0000 Features: 2Reference Feature(s): 47 142 -------------------------------------------------------------------------------- Step: 314 MM Cart Decimal Degree Construct XY Plane Comment: ANGLE 3mm hole #21 Line Actual Nominal Upper Tol. Lower Tol. p Sup. Angle +142.4848 -142.5000 +00.0000 +00.0000 X Location -061.8261 -061.8074 +00.0000 +00.0000 Y Location +047.4670 +047.4820 +00.0000 +00.0000 Z Location -002.3166 -002.3111 +00.0000 +00.0000 Straightness +000.0000 +00.0000 Features: 2Reference Feature(s): 145 47 -------------------------------------------------------------------------------- Step: 315 MM Cart Decimal Degree Construct XY Plane Comment: ANGLE 3mm hole #22 Line Actual Nominal Upper Tol. Lower Tol. p Angle +127.4735 +127.5000 +00.0000 +00.0000 X Location -047.4149 -047.3933 +00.0000 +00.0000 Y Location +061.8516 +061.8651 +00.0000 +00.0000 Z Location -002.2993 -002.2866 +00.0000 +00.0000 Straightness +000.0000 +00.0000 Features: 2Reference Feature(s): 47 148 -------------------------------------------------------------------------------- Step: 316 MM Cart Decimal Degree Construct XY Plane Comment: ANGLE 3mm hole #23 Line Actual Nominal Upper Tol. Lower Tol. p Angle +112.4642 +112.5000 +00.0000 +00.0000 X Location -031.4991 -031.4757 +00.0000 +00.0000 Y Location +076.1802 +076.1915 +00.0000 +00.0000 Z Location -002.3095 -002.3041 +00.0000 +00.0000 Straightness +000.0000 +00.0000 Features: 2Reference Feature(s): 47 151 -------------------------------------------------------------------------------- Step: 317 MM Cart Decimal Degree Construct XY Plane Comment: ANGLE 3 mm hole #24 Line Actual Nominal Upper Tol. Lower Tol. p Angle -082.5529 -082.5000 +00.0000 +00.0000 X Location -010.1019 -010.0783 +00.0000 +00.0000 Y Location +077.2827 +077.2909 +00.0000 +00.0000 Z Location -002.3028 -002.3026 +00.0000 +00.0000 Straightness +000.0000 +00.0000 Features: 2Reference Feature(s): 154 47 -------------------------------------------------------------------------------- Step: 318 MM Cart Decimal Degree Construct Comment: WIDTH 3mm hole #1 Width Actual Nominal Upper Tol. Lower Tol. p Width +155.8877 +156.0000 +00.0000 +00.0000 X Location +010.2638 +010.2875 +00.0000 +00.0000 Y Location +077.2651 +077.2708 +00.0000 +00.0000 Z Location -002.4961 -002.4811 +00.0000 +00.0000 p C/L Angle +172.4332 +172.4165 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 85 47 -------------------------------------------------------------------------------- Step: 319 MM Cart Decimal Degree Construct Comment: WIDTH 3mm hole #2 Width Actual Nominal Upper Tol. Lower Tol. p Width +164.9249 +165.0000 +00.0000 +00.0000 X Location +031.6593 +031.6828 +00.0000 +00.0000 Y Location +076.1429 +076.1459 +00.0000 +00.0000 Z Location -002.5813 -002.5821 +00.0000 +00.0000 p C/L Angle +157.4231 +157.4088 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 88 47 -------------------------------------------------------------------------------- Step: 320 MM Cart Decimal Degree Construct Comment: WIDTH 3mm hole #3 Width Actual Nominal Upper Tol. Lower Tol. p Width +155.9361 +156.0000 +00.0000 +00.0000 X Location +047.5541 +047.5756 +00.0000 +00.0000 Y Location +061.7869 +061.7874 +00.0000 +00.0000 Z Location -002.2938 -002.2834 +00.0000 +00.0000 p C/L Angle +142.4164 +142.4042 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 91 47 -------------------------------------------------------------------------------- Step: 321 MM Cart Decimal Degree Construct Comment: WIDTH 3mm hole #4 Width Actual Nominal Upper Tol. Lower Tol. p Width +155.9757 +156.0000 +00.0000 +00.0000 X Location +061.9493 +061.9692 +00.0000 +00.0000 Y Location +047.3749 +047.3736 +00.0000 +00.0000 Z Location -002.5553 -002.5431 +00.0000 +00.0000 p C/L Angle +127.4064 +127.3969 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 94 47 -------------------------------------------------------------------------------- Step: 322 MM Cart Decimal Degree Construct Comment: WIDTH 3mm hole #5 Width Actual Nominal Upper Tol. Lower Tol. p Width +165.0177 +165.0000 +00.0000 +00.0000 X Location +076.2783 +076.2956 +00.0000 +00.0000 Y Location +031.4537 +031.4504 +00.0000 +00.0000 Z Location -002.3556 -002.3469 +00.0000 +00.0000 p C/L Angle +112.4090 +112.4023 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 97 47 -------------------------------------------------------------------------------- Step: 323 MM Cart Decimal Degree Construct Comment: WIDTH 3mm hole #6 Width Actual Nominal Upper Tol. Lower Tol. p Width +156.0679 +156.0000 +00.0000 +00.0000 X Location +077.3824 +077.3969 +00.0000 +00.0000 Y Location +010.0634 +010.0592 +00.0000 +00.0000 Z Location -002.4738 -002.4634 +00.0000 +00.0000 p C/L Angle +097.4096 +097.4052 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 100 47 -------------------------------------------------------------------------------- Step: 324 MM Cart Decimal Degree Construct Comment: WIDTH 3mm hole #7 Width Actual Nominal Upper Tol. Lower Tol. p Width +156.1049 +156.0000 +00.0000 +00.0000 X Location +077.3703 +077.3818 +00.0000 +00.0000 Y Location -010.2972 -010.3016 +00.0000 +00.0000 Z Location -002.2858 -002.2749 +00.0000 +00.0000 p C/L Angle +082.4191 +082.4169 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 103 47 -------------------------------------------------------------------------------- Step: 325 MM Cart Decimal Degree Construct Comment: WIDTH 3mm hole #8 Width Actual Nominal Upper Tol. Lower Tol. p Width +165.1399 +165.0000 +00.0000 +00.0000 X Location +076.2451 +076.2536 +00.0000 +00.0000 Y Location -031.6936 -031.6977 +00.0000 +00.0000 Z Location -002.3378 -002.3324 +00.0000 +00.0000 p C/L Angle +067.4283 +067.4279 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 106 47 -------------------------------------------------------------------------------- Step: 326 MM Cart Decimal Degree Construct Comment: WIDTH 3mm hole #9 Width Actual Nominal Upper Tol. Lower Tol. p Width +156.1457 +156.0000 +00.0000 +00.0000 X Location +061.8891 +061.8952 +00.0000 +00.0000 Y Location -047.5932 -047.5954 +00.0000 +00.0000 Z Location -002.3498 -002.3496 +00.0000 +00.0000 p C/L Angle +052.4394 +052.4409 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 109 47 -------------------------------------------------------------------------------- Step: 327 MM Cart Decimal Degree Construct Comment: WIDTH 3mm hole #10 Width Actual Nominal Upper Tol. Lower Tol. p Width +156.1712 +156.0000 +00.0000 +00.0000 X Location +047.4778 +047.4818 +00.0000 +00.0000 Y Location -061.9937 -061.9936 +00.0000 +00.0000 Z Location -002.3458 -002.3399 +00.0000 +00.0000 p C/L Angle +037.4466 +037.4490 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 112 47 -------------------------------------------------------------------------------- Step: 328 MM Cart Decimal Degree Construct Comment: WIDTH 3mm hole #11 Width Actual Nominal Upper Tol. Lower Tol. p Width +165.1775 +165.0000 +00.0000 +00.0000 X Location +031.5500 +031.5521 +00.0000 +00.0000 Y Location -076.3249 -076.3230 +00.0000 +00.0000 Z Location -002.3521 -002.3479 +00.0000 +00.0000 p C/L Angle +022.4585 +022.4603 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 115 47 -------------------------------------------------------------------------------- Step: 329 MM Cart Decimal Degree Construct Comment: WIDTH 3mm hole #12 Width Actual Nominal Upper Tol. Lower Tol. p Width +156.1645 +156.0000 +00.0000 +00.0000 X Location +010.1655 +010.1672 +00.0000 +00.0000 Y Location -077.4177 -077.4128 +00.0000 +00.0000 Z Location -002.3253 -002.3096 +00.0000 +00.0000 p C/L Angle +007.4805 +007.4823 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 118 47 -------------------------------------------------------------------------------- Step: 330 MM Cart Decimal Degree Construct Comment: WIDTH 3mm hole #13 Width Actual Nominal Upper Tol. Lower Tol. p Width +156.1466 +156.0000 +00.0000 +00.0000 X Location -010.2188 -010.2172 +00.0000 +00.0000 Y Location -077.4016 -077.3938 +00.0000 +00.0000 Z Location -002.4001 -002.4109 +00.0000 +00.0000 p C/L Angle +172.4791 +172.4796 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 121 47 -------------------------------------------------------------------------------- Step: 331 MM Cart Decimal Degree Construct Comment: WIDTH 3mm hole #14 Width Actual Nominal Upper Tol. Lower Tol. p Width +165.1105 +165.0000 +00.0000 +00.0000 X Location -031.5922 -031.5905 +00.0000 +00.0000 Y Location -076.2712 -076.2611 +00.0000 +00.0000 Z Location -002.3118 -002.3029 +00.0000 +00.0000 p C/L Angle +157.5002 +157.4986 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 124 47 -------------------------------------------------------------------------------- Step: 332 MM Cart Decimal Degree Construct Comment: WIDTH 3mm hole #15 Width Actual Nominal Upper Tol. Lower Tol. p Width +156.0817 +156.0000 +00.0000 +00.0000 X Location -047.4941 -047.4908 +00.0000 +00.0000 Y Location -061.9248 -061.9115 +00.0000 +00.0000 Z Location -002.3601 -002.3416 +00.0000 +00.0000 p C/L Angle +142.5131 +142.5091 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 127 47 -------------------------------------------------------------------------------- Step: 333 MM Cart Decimal Degree Construct Comment: WIDTH 3mm hole #16 Width Actual Nominal Upper Tol. Lower Tol. p Width +156.0447 +156.0000 +00.0000 +00.0000 X Location -061.8866 -061.8812 +00.0000 +00.0000 Y Location -047.5135 -047.4988 +00.0000 +00.0000 Z Location -002.4983 -002.4861 +00.0000 +00.0000 p C/L Angle +127.5153 +127.5091 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 130 47 -------------------------------------------------------------------------------- Step: 334 MM Cart Decimal Degree Construct Comment: WIDTH 3mm hole #17 Width Actual Nominal Upper Tol. Lower Tol. p Width +165.0112 +165.0000 +00.0000 +00.0000 X Location -076.2183 -076.2105 +00.0000 +00.0000 Y Location -031.5902 -031.5735 +00.0000 +00.0000 Z Location -002.3443 -002.3366 +00.0000 +00.0000 p C/L Angle +112.5125 +112.5039 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 47 133 -------------------------------------------------------------------------------- Step: 335 MM Cart Decimal Degree Construct Comment: WIDTH 3mm hole #18 Width Actual Nominal Upper Tol. Lower Tol. p Width +155.9688 +156.0000 +00.0000 +00.0000 X Location -077.3149 -077.3043 +00.0000 +00.0000 Y Location -010.1967 -010.1795 +00.0000 +00.0000 Z Location -002.3221 -002.3059 +00.0000 +00.0000 p C/L Angle +097.5131 +097.5016 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 136 47 -------------------------------------------------------------------------------- Step: 336 MM Cart Decimal Degree Construct Comment: WIDTH 3mm hole #19 Width Actual Nominal Upper Tol. Lower Tol. p Width +155.9372 +156.0000 +00.0000 +00.0000 X Location -077.3011 -077.2873 +00.0000 +00.0000 Y Location +010.1803 +010.1974 +00.0000 +00.0000 Z Location -002.4778 -002.4679 +00.0000 +00.0000 p C/L Angle +082.4975 +082.4837 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 47 139 -------------------------------------------------------------------------------- Step: 337 MM Cart Decimal Degree Construct Comment: WIDTH 3mm hole #20 Width Actual Nominal Upper Tol. Lower Tol. p Width +164.9223 +165.0000 +00.0000 +00.0000 X Location -076.1813 -076.1645 +00.0000 +00.0000 Y Location +031.5635 +031.5802 +00.0000 +00.0000 Z Location -002.3168 -002.3096 +00.0000 +00.0000 p C/L Angle +067.4948 +067.4795 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 47 142 -------------------------------------------------------------------------------- Step: 338 MM Cart Decimal Degree Construct Comment: WIDTH 3mm hole #21 Width Actual Nominal Upper Tol. Lower Tol. p Width +155.8921 +156.0000 +00.0000 +00.0000 X Location -061.8261 -061.8074 +00.0000 +00.0000 Y Location +047.4670 +047.4820 +00.0000 +00.0000 Z Location -002.3166 -002.3111 +00.0000 +00.0000 p C/L Angle +052.4848 +052.4676 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 47 145 -------------------------------------------------------------------------------- Step: 339 MM Cart Decimal Degree Construct Comment: WIDTH 3mm hole #22 Width Actual Nominal Upper Tol. Lower Tol. p Width +155.8691 +156.0000 +00.0000 +00.0000 X Location -047.4149 -047.3933 +00.0000 +00.0000 Y Location +061.8516 +061.8651 +00.0000 +00.0000 Z Location -002.2993 -002.2866 +00.0000 +00.0000 p C/L Angle +037.4735 +037.4549 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 47 148 -------------------------------------------------------------------------------- Step: 340 MM Cart Decimal Degree Construct Comment: WIDTH 3mm hole #23 Width Actual Nominal Upper Tol. Lower Tol. p Width +164.8710 +165.0000 +00.0000 +00.0000 X Location -031.4991 -031.4757 +00.0000 +00.0000 Y Location +076.1802 +076.1915 +00.0000 +00.0000 Z Location -002.3095 -002.3041 +00.0000 +00.0000 p C/L Angle +022.4642 +022.4461 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 47 151 -------------------------------------------------------------------------------- Step: 341 MM Cart Decimal Degree Construct Comment: WIDTH 3mm hole #24 Width Actual Nominal Upper Tol. Lower Tol. p Width +155.8803 +156.0000 +00.0000 +00.0000 X Location -010.1019 -010.0783 +00.0000 +00.0000 Y Location +077.2827 +077.2909 +00.0000 +00.0000 Z Location -002.3028 -002.3026 +00.0000 +00.0000 p C/L Angle +007.4471 +007.4292 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 47 154 -------------------------------------------------------------------------------- Step: 342 MM Cart Decimal Degree Construct Comment: Width holes 1 and 2 Width Actual Nominal Upper Tol. Lower Tol. p Width +042.8497 +042.8497 +00.0000 +00.0000 p X Location +041.9231 +041.9703 +00.0000 +00.0000 p Y Location +153.4081 +153.4167 +00.0000 +00.0000 Z Location +001.3313 +001.3182 +00.0000 +00.0000 p C/L Angle +086.9976 +086.9903 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 85 88 -------------------------------------------------------------------------------- Step: 343 MM Cart Decimal Degree Construct Comment: WIDTH holes 2 & 3 Width Actual Nominal Upper Tol. Lower Tol. p Width +042.8365 +042.8367 +00.0000 +00.0000 p X Location +079.2134 +079.2584 +00.0000 +00.0000 p Y Location +137.9298 +137.9333 +00.0000 +00.0000 Z Location +001.5336 +001.5160 +00.0000 +00.0000 p C/L Angle +047.9120 +047.9035 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 88 91 -------------------------------------------------------------------------------- Step: 344 MM Cart Decimal Degree Construct Comment: WIDTH holes 1 & 3 Width Actual Nominal Upper Tol. Lower Tol. p Width +080.7500 +080.7499 +00.0000 +00.0000 p X Location +057.8180 +057.8631 +00.0000 +00.0000 p Y Location +139.0520 +139.0582 +00.0000 +00.0000 Z Location +001.6189 +001.6170 +00.0000 +00.0000 p C/L Angle +067.4579 +067.4500 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 91 85 -------------------------------------------------------------------------------- Step: 345 MM Cart Decimal Degree Construct Comment: WIDTH holes 4 & 5 Width Actual Nominal Upper Tol. Lower Tol. p Width +042.8394 +042.8390 +00.0000 +00.0000 p X Location +138.2276 +138.2647 +00.0000 +00.0000 p Y Location +078.8286 +078.8240 +00.0000 +00.0000 Z Location +001.4978 +001.4915 +00.0000 +00.0000 p C/L Angle +041.9870 +041.9782 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 94 97 -------------------------------------------------------------------------------- Step: 346 MM Cart Decimal Degree Construct Comment: WIDTH holes 5 & 6 Width Actual Nominal Upper Tol. Lower Tol. p Width +042.8376 +042.8391 +00.0000 +00.0000 p X Location +153.6607 +153.6925 +00.0000 +00.0000 p Y Location +041.5171 +041.5096 +00.0000 +00.0000 Z Location +001.5793 +001.5713 +00.0000 +00.0000 p C/L Angle +002.9547 +002.9473 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 97 100 -------------------------------------------------------------------------------- Step: 347 MM Cart Decimal Degree Construct Comment: WIDTH holes 4 & 6 Width Actual Nominal Upper Tol. Lower Tol. p Width +080.7546 +080.7560 +00.0000 +00.0000 p X Location +139.3317 +139.3661 +00.0000 +00.0000 p Y Location +057.4383 +057.4328 +00.0000 +00.0000 Z Location +001.3796 +001.3750 +00.0000 +00.0000 p C/L Angle +022.4713 +022.4628 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 100 94 -------------------------------------------------------------------------------- Step: 348 MM Cart Decimal Degree Construct Comment: WIDTH holes 7 & 8 Width Actual Nominal Upper Tol. Lower Tol. p Width +042.8519 +042.8516 +00.0000 +00.0000 p X Location +153.6154 +153.6353 +00.0000 +00.0000 p Y Location -041.9907 -041.9994 +00.0000 +00.0000 Z Location +001.7851 +001.7743 +00.0000 +00.0000 p C/L Angle +176.9898 +176.9816 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 103 106 -------------------------------------------------------------------------------- Step: 349 MM Cart Decimal Degree Construct Comment: WIDTH holes 8 & 9 Width Actual Nominal Upper Tol. Lower Tol. p Width +042.8436 +042.8439 +00.0000 +00.0000 p X Location +138.1342 +138.1487 +00.0000 +00.0000 p Y Location -079.2867 -079.2931 +00.0000 +00.0000 Z Location +001.7211 +001.6995 +00.0000 +00.0000 p C/L Angle +137.9206 +137.9124 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 106 109 -------------------------------------------------------------------------------- Step: 350 MM Cart Decimal Degree Construct Comment: WIDTH holes 7 & 9 Width Actual Nominal Upper Tol. Lower Tol. p Width +080.7628 +080.7628 +00.0000 +00.0000 p X Location +139.2593 +139.2770 +00.0000 +00.0000 p Y Location -057.8903 -057.8970 +00.0000 +00.0000 Z Location +001.7731 +001.7570 +00.0000 +00.0000 p C/L Angle +157.4572 +157.4488 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 109 103 -------------------------------------------------------------------------------- Step: 351 MM Cart Decimal Degree Construct Comment: WIDTH holes 10 & 11 Width Actual Nominal Upper Tol. Lower Tol. p Width +042.8522 +042.8527 +00.0000 +00.0000 p X Location +079.0278 +079.0339 +00.0000 +00.0000 p Y Location -138.3186 -138.3166 +00.0000 +00.0000 Z Location +001.7109 +001.6938 +00.0000 +00.0000 p C/L Angle +131.9798 +131.9724 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 112 115 -------------------------------------------------------------------------------- Step: 352 MM Cart Decimal Degree Construct Comment: WIDTH holes 11 & 12 Width Actual Nominal Upper Tol. Lower Tol. p Width +042.8249 +042.8252 +00.0000 +00.0000 p X Location +041.7155 +041.7193 +00.0000 +00.0000 p Y Location -153.7426 -153.7358 +00.0000 +00.0000 Z Location +001.7314 +001.7240 +00.0000 +00.0000 p C/L Angle +092.9253 +092.9174 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 115 118 -------------------------------------------------------------------------------- Step: 353 MM Cart Decimal Degree Construct Comment: WIDTH holes 10 & 12 Width Actual Nominal Upper Tol. Lower Tol. p Width +080.7491 +080.7498 +00.0000 +00.0000 p X Location +057.6433 +057.6490 +00.0000 +00.0000 p Y Location -139.4114 -139.4064 +00.0000 +00.0000 Z Location +001.7376 +001.7320 +00.0000 +00.0000 p C/L Angle +112.4590 +112.4514 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 118 112 -------------------------------------------------------------------------------- Step: 354 MM Cart Decimal Degree Construct Comment: WIDTH holes 13 & 14 Width Actual Nominal Upper Tol. Lower Tol. p Width +042.8065 +042.8067 +00.0000 +00.0000 p X Location -041.8111 -041.8077 +00.0000 +00.0000 p Y Location -153.6729 -153.6549 +00.0000 +00.0000 Z Location +001.6969 +001.6678 +00.0000 +00.0000 p C/L Angle +086.9725 +086.9664 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 121 124 -------------------------------------------------------------------------------- Step: 355 MM Cart Decimal Degree Construct Comment: WIDTH holes 14 & 15 Width Actual Nominal Upper Tol. Lower Tol. p Width +042.8341 +042.8360 +00.0000 +00.0000 p X Location -079.0863 -079.0813 +00.0000 +00.0000 p Y Location -138.1960 -138.1726 +00.0000 +00.0000 Z Location +001.7369 +001.7370 +00.0000 +00.0000 p C/L Angle +047.9438 +047.9346 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 124 127 -------------------------------------------------------------------------------- Step: 356 MM Cart Decimal Degree Construct Comment: WIDTH holes 13 & 15 Width Actual Nominal Upper Tol. Lower Tol. p Width +080.7212 +080.7224 +00.0000 +00.0000 p X Location -057.7130 -057.7080 +00.0000 +00.0000 p Y Location -139.3264 -139.3053 +00.0000 +00.0000 Z Location +001.6486 +001.6290 +00.0000 +00.0000 p C/L Angle +067.4516 +067.4435 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 127 121 -------------------------------------------------------------------------------- Step: 357 MM Cart Decimal Degree Construct Comment: WIDTH holes 16 & 17 Width Actual Nominal Upper Tol. Lower Tol. p Width +042.8461 +042.8460 +00.0000 +00.0000 p X Location -138.1049 -138.0917 +00.0000 +00.0000 p Y Location -079.1037 -079.0722 +00.0000 +00.0000 Z Location +001.5661 +001.5588 +00.0000 +00.0000 p C/L Angle +041.9887 +041.9804 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 130 133 -------------------------------------------------------------------------------- Step: 358 MM Cart Decimal Degree Construct Comment: WIDTH holes 17 & 18 Width Actual Nominal Upper Tol. Lower Tol. p Width +042.8432 +042.8439 +00.0000 +00.0000 p X Location -153.5332 -153.5148 +00.0000 +00.0000 p Y Location -041.7869 -041.7529 +00.0000 +00.0000 Z Location +001.7424 +001.7390 +00.0000 +00.0000 p C/L Angle +002.9343 +002.9267 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 133 136 -------------------------------------------------------------------------------- Step: 359 MM Cart Decimal Degree Construct Comment: WIDTH holes 16 & 18 Width Actual Nominal Upper Tol. Lower Tol. p Width +080.7607 +080.7614 +00.0000 +00.0000 p X Location -139.2015 -139.1854 +00.0000 +00.0000 p Y Location -057.7102 -057.6782 +00.0000 +00.0000 Z Location +001.5883 +001.5895 +00.0000 +00.0000 p C/L Angle +022.4622 +022.4540 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 136 130 -------------------------------------------------------------------------------- Step: 360 MM Cart Decimal Degree Construct Comment: WIDTH holes 19 & 20 Width Actual Nominal Upper Tol. Lower Tol. p Width +042.8250 +042.8246 +00.0000 +00.0000 p X Location -153.4824 -153.4517 +00.0000 +00.0000 p Y Location +041.7437 +041.7777 +00.0000 +00.0000 Z Location +001.6141 +001.6040 +00.0000 +00.0000 p C/L Angle +177.0021 +176.9942 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 139 142 -------------------------------------------------------------------------------- Step: 361 MM Cart Decimal Degree Construct Comment: Width holes 20 & 21 Width Actual Nominal Upper Tol. Lower Tol. p Width +042.8481 +042.8482 +00.0000 +00.0000 p X Location -138.0074 -137.9719 +00.0000 +00.0000 p Y Location +079.0304 +079.0622 +00.0000 +00.0000 Z Location +001.7754 +001.7608 +00.0000 +00.0000 p C/L Angle +137.9293 +137.9223 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 142 145 -------------------------------------------------------------------------------- Step: 362 MM Cart Decimal Degree Construct Comment: WIDTH holes 19 & 21 Width Actual Nominal Upper Tol. Lower Tol. p Width +080.7409 +080.7407 +00.0000 +00.0000 p X Location -139.1273 -139.0947 +00.0000 +00.0000 p Y Location +057.6472 +057.6794 +00.0000 +00.0000 Z Location +001.6144 +001.6025 +00.0000 +00.0000 p C/L Angle +157.4602 +157.4527 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 145 139 -------------------------------------------------------------------------------- Step: 363 MM Cart Decimal Degree Construct Comment: WIDTH holes 22 & 23 Width Actual Nominal Upper Tol. Lower Tol. p Width +042.8309 +042.8308 +00.0000 +00.0000 p X Location -078.9141 -078.8690 +00.0000 +00.0000 p Y Location +138.0317 +138.0566 +00.0000 +00.0000 Z Location +001.7999 +001.7908 +00.0000 +00.0000 p C/L Angle +131.9959 +131.9883 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 148 151 -------------------------------------------------------------------------------- Step: 364 MM Cart Decimal Degree Construct Comment: WIDTH holes 23 & 24 Width Actual Nominal Upper Tol. Lower Tol. p Width +042.8513 +042.8511 +00.0000 +00.0000 p X Location -041.6010 -041.5540 +00.0000 +00.0000 p Y Location +153.4629 +153.4824 +00.0000 +00.0000 Z Location +001.7964 +001.7748 +00.0000 +00.0000 p C/L Angle +092.9498 +092.9412 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 151 154 -------------------------------------------------------------------------------- Step: 365 MM Cart Decimal Degree Construct Comment: WIDTH holes 23 & 24 Width Actual Nominal Upper Tol. Lower Tol. p Width +080.7561 +080.7556 +00.0000 +00.0000 p X Location -057.5168 -057.4717 +00.0000 +00.0000 p Y Location +139.1343 +139.1560 +00.0000 +00.0000 Z Location +001.8066 +001.7923 +00.0000 +00.0000 p C/L Angle +112.4680 +112.4599 +00.0000 +00.0000 True Position Tolerance +00.0000 RFS Features: 2Reference Feature(s): 154 148 --------------------------------------------------------------------------------